Added back some TCP/IP stack port layer files.
This commit is contained in:
Richard Barry
parent
7cf721ccf7
commit
9c0c37ab9b
@ -0,0 +1,721 @@
|
|||||||
|
/*
|
||||||
|
* Handling of Ethernet PHY's
|
||||||
|
* PHY's communicate with an EMAC either through
|
||||||
|
* a Media-Independent Interface (MII), or a Reduced Media-Independent Interface (RMII).
|
||||||
|
* The EMAC can poll for PHY ports on 32 different addresses. Each of the PHY ports
|
||||||
|
* shall be treated independently.
|
||||||
|
*
|
||||||
|
*/
|
||||||
|
|
||||||
|
/* Standard includes. */
|
||||||
|
#include <stdint.h>
|
||||||
|
#include <stdio.h>
|
||||||
|
#include <stdlib.h>
|
||||||
|
|
||||||
|
/* FreeRTOS includes. */
|
||||||
|
#include "FreeRTOS.h"
|
||||||
|
#include "task.h"
|
||||||
|
#include "queue.h"
|
||||||
|
#include "semphr.h"
|
||||||
|
|
||||||
|
/* FreeRTOS+TCP includes. */
|
||||||
|
#include "FreeRTOS_IP.h"
|
||||||
|
#include "FreeRTOS_Sockets.h"
|
||||||
|
|
||||||
|
#include "phyHandling.h"
|
||||||
|
|
||||||
|
#define phyMIN_PHY_ADDRESS 0
|
||||||
|
#define phyMAX_PHY_ADDRESS 31
|
||||||
|
|
||||||
|
#if defined( PHY_LS_HIGH_CHECK_TIME_MS ) || defined( PHY_LS_LOW_CHECK_TIME_MS )
|
||||||
|
#warning please use the new defines with 'ipconfig' prefix
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#ifndef ipconfigPHY_LS_HIGH_CHECK_TIME_MS
|
||||||
|
/* Check if the LinkStatus in the PHY is still high after 15 seconds of not
|
||||||
|
receiving packets. */
|
||||||
|
#define ipconfigPHY_LS_HIGH_CHECK_TIME_MS 15000uL
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#ifndef ipconfigPHY_LS_LOW_CHECK_TIME_MS
|
||||||
|
/* Check if the LinkStatus in the PHY is still low every second. */
|
||||||
|
#define ipconfigPHY_LS_LOW_CHECK_TIME_MS 1000uL
|
||||||
|
#endif
|
||||||
|
|
||||||
|
/* As the following 3 macro's are OK in most situations, and so they're not
|
||||||
|
included in 'FreeRTOSIPConfigDefaults.h'.
|
||||||
|
Users can change their values in the project's 'FreeRTOSIPConfig.h'. */
|
||||||
|
#ifndef phyPHY_MAX_RESET_TIME_MS
|
||||||
|
#define phyPHY_MAX_RESET_TIME_MS 1000uL
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#ifndef phyPHY_MAX_NEGOTIATE_TIME_MS
|
||||||
|
#define phyPHY_MAX_NEGOTIATE_TIME_MS 3000uL
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#ifndef phySHORT_DELAY_MS
|
||||||
|
#define phySHORT_DELAY_MS 50uL
|
||||||
|
#endif
|
||||||
|
|
||||||
|
/* Naming and numbering of basic PHY registers. */
|
||||||
|
#define phyREG_00_BMCR 0x00u /* Basic Mode Control Register. */
|
||||||
|
#define phyREG_01_BMSR 0x01u /* Basic Mode Status Register. */
|
||||||
|
#define phyREG_02_PHYSID1 0x02u /* PHYS ID 1 */
|
||||||
|
#define phyREG_03_PHYSID2 0x03u /* PHYS ID 2 */
|
||||||
|
#define phyREG_04_ADVERTISE 0x04u /* Advertisement control reg */
|
||||||
|
|
||||||
|
/* Naming and numbering of extended PHY registers. */
|
||||||
|
#define PHYREG_10_PHYSTS 0x10u /* 16 PHY status register Offset */
|
||||||
|
#define phyREG_19_PHYCR 0x19u /* 25 RW PHY Control Register */
|
||||||
|
#define phyREG_1F_PHYSPCS 0x1Fu /* 31 RW PHY Special Control Status */
|
||||||
|
|
||||||
|
/* Bit fields for 'phyREG_00_BMCR', the 'Basic Mode Control Register'. */
|
||||||
|
#define phyBMCR_FULL_DUPLEX 0x0100u /* Full duplex. */
|
||||||
|
#define phyBMCR_AN_RESTART 0x0200u /* Auto negotiation restart. */
|
||||||
|
#define phyBMCR_ISOLATE 0x0400u /* 1 = Isolates 0 = Normal operation. */
|
||||||
|
#define phyBMCR_AN_ENABLE 0x1000u /* Enable auto negotiation. */
|
||||||
|
#define phyBMCR_SPEED_100 0x2000u /* Select 100Mbps. */
|
||||||
|
#define phyBMCR_RESET 0x8000u /* Reset the PHY. */
|
||||||
|
|
||||||
|
/* Bit fields for 'phyREG_19_PHYCR', the 'PHY Control Register'. */
|
||||||
|
#define PHYCR_MDIX_EN 0x8000u /* Enable Auto MDIX. */
|
||||||
|
#define PHYCR_MDIX_FORCE 0x4000u /* Force MDIX crossed. */
|
||||||
|
|
||||||
|
#define phyBMSR_AN_COMPLETE 0x0020u /* Auto-Negotiation process completed */
|
||||||
|
|
||||||
|
#define phyBMSR_LINK_STATUS 0x0004u
|
||||||
|
|
||||||
|
#define phyPHYSTS_LINK_STATUS 0x0001u /* PHY Link mask */
|
||||||
|
#define phyPHYSTS_SPEED_STATUS 0x0002u /* PHY Speed mask */
|
||||||
|
#define phyPHYSTS_DUPLEX_STATUS 0x0004u /* PHY Duplex mask */
|
||||||
|
|
||||||
|
/* Bit fields for 'phyREG_1F_PHYSPCS
|
||||||
|
001 = 10BASE-T half-duplex
|
||||||
|
101 = 10BASE-T full-duplex
|
||||||
|
010 = 100BASE-TX half-duplex
|
||||||
|
110 = 100BASE-TX full-duplex
|
||||||
|
*/
|
||||||
|
#define phyPHYSPCS_SPEED_MASK 0x000Cu
|
||||||
|
#define phyPHYSPCS_SPEED_10 0x0004u
|
||||||
|
#define phyPHYSPCS_FULL_DUPLEX 0x0010u
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Description of all capabilities that can be advertised to
|
||||||
|
* the peer (usually a switch or router).
|
||||||
|
*/
|
||||||
|
|
||||||
|
#define phyADVERTISE_CSMA 0x0001u /* Supports IEEE 802.3u: Fast Ethernet at 100 Mbit/s */
|
||||||
|
#define phyADVERTISE_10HALF 0x0020u /* Try for 10mbps half-duplex. */
|
||||||
|
#define phyADVERTISE_10FULL 0x0040u /* Try for 10mbps full-duplex. */
|
||||||
|
#define phyADVERTISE_100HALF 0x0080u /* Try for 100mbps half-duplex. */
|
||||||
|
#define phyADVERTISE_100FULL 0x0100u /* Try for 100mbps full-duplex. */
|
||||||
|
|
||||||
|
#define phyADVERTISE_ALL ( phyADVERTISE_10HALF | phyADVERTISE_10FULL | \
|
||||||
|
phyADVERTISE_100HALF | phyADVERTISE_100FULL | \
|
||||||
|
phyADVERTISE_CSMA )
|
||||||
|
|
||||||
|
/* Send a reset command to a set of PHY-ports. */
|
||||||
|
static uint32_t xPhyReset( EthernetPhy_t *pxPhyObject, uint32_t ulPhyMask );
|
||||||
|
|
||||||
|
static BaseType_t xHas_1F_PHYSPCS( uint32_t ulPhyID )
|
||||||
|
{
|
||||||
|
BaseType_t xResult;
|
||||||
|
|
||||||
|
switch( ulPhyID )
|
||||||
|
{
|
||||||
|
case PHY_ID_LAN8720:
|
||||||
|
case PHY_ID_LAN8742A:
|
||||||
|
case PHY_ID_KSZ8041:
|
||||||
|
/*
|
||||||
|
case PHY_ID_KSZ8051: // same ID as 8041
|
||||||
|
case PHY_ID_KSZ8081: // same ID as 8041
|
||||||
|
*/
|
||||||
|
case PHY_ID_KSZ8081MNXIA:
|
||||||
|
|
||||||
|
case PHY_ID_KSZ8863:
|
||||||
|
default:
|
||||||
|
/* Most PHY's have a 1F_PHYSPCS */
|
||||||
|
xResult = pdTRUE;
|
||||||
|
break;
|
||||||
|
case PHY_ID_DP83848I:
|
||||||
|
xResult = pdFALSE;
|
||||||
|
break;
|
||||||
|
}
|
||||||
|
return xResult;
|
||||||
|
}
|
||||||
|
/*-----------------------------------------------------------*/
|
||||||
|
|
||||||
|
static BaseType_t xHas_19_PHYCR( uint32_t ulPhyID )
|
||||||
|
{
|
||||||
|
BaseType_t xResult;
|
||||||
|
|
||||||
|
switch( ulPhyID )
|
||||||
|
{
|
||||||
|
case PHY_ID_LAN8742A:
|
||||||
|
case PHY_ID_DP83848I:
|
||||||
|
xResult = pdTRUE;
|
||||||
|
break;
|
||||||
|
default:
|
||||||
|
/* Most PHY's do not have a 19_PHYCR */
|
||||||
|
xResult = pdFALSE;
|
||||||
|
break;
|
||||||
|
}
|
||||||
|
return xResult;
|
||||||
|
}
|
||||||
|
/*-----------------------------------------------------------*/
|
||||||
|
|
||||||
|
/* Initialise the struct and assign a PHY-read and -write function. */
|
||||||
|
void vPhyInitialise( EthernetPhy_t *pxPhyObject, xApplicationPhyReadHook_t fnPhyRead, xApplicationPhyWriteHook_t fnPhyWrite )
|
||||||
|
{
|
||||||
|
memset( ( void * )pxPhyObject, '\0', sizeof( *pxPhyObject ) );
|
||||||
|
|
||||||
|
pxPhyObject->fnPhyRead = fnPhyRead;
|
||||||
|
pxPhyObject->fnPhyWrite = fnPhyWrite;
|
||||||
|
}
|
||||||
|
/*-----------------------------------------------------------*/
|
||||||
|
|
||||||
|
/* Discover all PHY's connected by polling 32 indexes ( zero-based ) */
|
||||||
|
BaseType_t xPhyDiscover( EthernetPhy_t *pxPhyObject )
|
||||||
|
{
|
||||||
|
BaseType_t xPhyAddress;
|
||||||
|
|
||||||
|
pxPhyObject->xPortCount = 0;
|
||||||
|
|
||||||
|
for( xPhyAddress = phyMIN_PHY_ADDRESS; xPhyAddress <= phyMAX_PHY_ADDRESS; xPhyAddress++ )
|
||||||
|
{
|
||||||
|
uint32_t ulLowerID;
|
||||||
|
|
||||||
|
pxPhyObject->fnPhyRead( xPhyAddress, phyREG_03_PHYSID2, &ulLowerID );
|
||||||
|
/* A valid PHY id can not be all zeros or all ones. */
|
||||||
|
if( ( ulLowerID != ( uint16_t )~0u ) && ( ulLowerID != ( uint16_t )0u ) )
|
||||||
|
{
|
||||||
|
uint32_t ulUpperID;
|
||||||
|
uint32_t ulPhyID;
|
||||||
|
|
||||||
|
pxPhyObject->fnPhyRead( xPhyAddress, phyREG_02_PHYSID1, &ulUpperID );
|
||||||
|
ulPhyID = ( ( ( uint32_t ) ulUpperID ) << 16 ) | ( ulLowerID & 0xFFF0 );
|
||||||
|
|
||||||
|
pxPhyObject->ucPhyIndexes[ pxPhyObject->xPortCount ] = xPhyAddress;
|
||||||
|
pxPhyObject->ulPhyIDs[ pxPhyObject->xPortCount ] = ulPhyID;
|
||||||
|
|
||||||
|
pxPhyObject->xPortCount++;
|
||||||
|
|
||||||
|
/* See if there is more storage space. */
|
||||||
|
if( pxPhyObject->xPortCount == ipconfigPHY_MAX_PORTS )
|
||||||
|
{
|
||||||
|
break;
|
||||||
|
}
|
||||||
|
}
|
||||||
|
}
|
||||||
|
if( pxPhyObject->xPortCount > 0 )
|
||||||
|
{
|
||||||
|
FreeRTOS_printf( ( "PHY ID %lX\n", pxPhyObject->ulPhyIDs[ 0 ] ) );
|
||||||
|
}
|
||||||
|
|
||||||
|
return pxPhyObject->xPortCount;
|
||||||
|
}
|
||||||
|
/*-----------------------------------------------------------*/
|
||||||
|
|
||||||
|
/* Send a reset command to a set of PHY-ports. */
|
||||||
|
static uint32_t xPhyReset( EthernetPhy_t *pxPhyObject, uint32_t ulPhyMask )
|
||||||
|
{
|
||||||
|
uint32_t ulDoneMask, ulConfig;
|
||||||
|
TickType_t xRemainingTime;
|
||||||
|
TimeOut_t xTimer;
|
||||||
|
BaseType_t xPhyIndex;
|
||||||
|
|
||||||
|
/* A bit-mask of PHY ports that are ready. */
|
||||||
|
ulDoneMask = 0ul;
|
||||||
|
|
||||||
|
/* Set the RESET bits high. */
|
||||||
|
for( xPhyIndex = 0; xPhyIndex < pxPhyObject->xPortCount; xPhyIndex++ )
|
||||||
|
{
|
||||||
|
BaseType_t xPhyAddress = pxPhyObject->ucPhyIndexes[ xPhyIndex ];
|
||||||
|
|
||||||
|
/* Read Control register. */
|
||||||
|
pxPhyObject->fnPhyRead( xPhyAddress, phyREG_00_BMCR, &ulConfig );
|
||||||
|
pxPhyObject->fnPhyWrite( xPhyAddress, phyREG_00_BMCR, ulConfig | phyBMCR_RESET );
|
||||||
|
}
|
||||||
|
|
||||||
|
xRemainingTime = ( TickType_t ) pdMS_TO_TICKS( phyPHY_MAX_RESET_TIME_MS );
|
||||||
|
vTaskSetTimeOutState( &xTimer );
|
||||||
|
|
||||||
|
/* The reset should last less than a second. */
|
||||||
|
for( ;; )
|
||||||
|
{
|
||||||
|
for( xPhyIndex = 0; xPhyIndex < pxPhyObject->xPortCount; xPhyIndex++ )
|
||||||
|
{
|
||||||
|
BaseType_t xPhyAddress = pxPhyObject->ucPhyIndexes[ xPhyIndex ];
|
||||||
|
|
||||||
|
pxPhyObject->fnPhyRead( xPhyAddress, phyREG_00_BMCR, &ulConfig );
|
||||||
|
if( ( ulConfig & phyBMCR_RESET ) == 0 )
|
||||||
|
{
|
||||||
|
FreeRTOS_printf( ( "xPhyReset: phyBMCR_RESET %d ready\n", (int)xPhyIndex ) );
|
||||||
|
ulDoneMask |= ( 1ul << xPhyIndex );
|
||||||
|
}
|
||||||
|
}
|
||||||
|
if( ulDoneMask == ulPhyMask )
|
||||||
|
{
|
||||||
|
break;
|
||||||
|
}
|
||||||
|
if( xTaskCheckForTimeOut( &xTimer, &xRemainingTime ) != pdFALSE )
|
||||||
|
{
|
||||||
|
FreeRTOS_printf( ( "xPhyReset: phyBMCR_RESET timed out ( done 0x%02lX )\n", ulDoneMask ) );
|
||||||
|
break;
|
||||||
|
}
|
||||||
|
/* Block for a while */
|
||||||
|
vTaskDelay( pdMS_TO_TICKS( phySHORT_DELAY_MS ) );
|
||||||
|
}
|
||||||
|
|
||||||
|
/* Clear the reset bits. */
|
||||||
|
for( xPhyIndex = 0; xPhyIndex < pxPhyObject->xPortCount; xPhyIndex++ )
|
||||||
|
{
|
||||||
|
if( ( ulDoneMask & ( 1ul << xPhyIndex ) ) == 0uL )
|
||||||
|
{
|
||||||
|
BaseType_t xPhyAddress = pxPhyObject->ucPhyIndexes[ xPhyIndex ];
|
||||||
|
|
||||||
|
/* The reset operation timed out, clear the bit manually. */
|
||||||
|
pxPhyObject->fnPhyRead( xPhyAddress, phyREG_00_BMCR, &ulConfig );
|
||||||
|
pxPhyObject->fnPhyWrite( xPhyAddress, phyREG_00_BMCR, ulConfig & ~phyBMCR_RESET );
|
||||||
|
}
|
||||||
|
}
|
||||||
|
|
||||||
|
vTaskDelay( pdMS_TO_TICKS( phySHORT_DELAY_MS ) );
|
||||||
|
|
||||||
|
return ulDoneMask;
|
||||||
|
}
|
||||||
|
/*-----------------------------------------------------------*/
|
||||||
|
|
||||||
|
BaseType_t xPhyConfigure( EthernetPhy_t *pxPhyObject, const PhyProperties_t *pxPhyProperties )
|
||||||
|
{
|
||||||
|
uint32_t ulConfig, ulAdvertise;
|
||||||
|
BaseType_t xPhyIndex;
|
||||||
|
|
||||||
|
if( pxPhyObject->xPortCount < 1 )
|
||||||
|
{
|
||||||
|
FreeRTOS_printf( ( "xPhyConfigure: No PHY's detected.\n" ) );
|
||||||
|
return -1;
|
||||||
|
}
|
||||||
|
|
||||||
|
/* The expected ID for the 'LAN8742A' is 0x0007c130. */
|
||||||
|
/* The expected ID for the 'LAN8720' is 0x0007c0f0. */
|
||||||
|
/* The expected ID for the 'DP83848I' is 0x20005C90. */
|
||||||
|
|
||||||
|
/* Set advertise register. */
|
||||||
|
if( ( pxPhyProperties->ucSpeed == ( uint8_t )PHY_SPEED_AUTO ) && ( pxPhyProperties->ucDuplex == ( uint8_t )PHY_DUPLEX_AUTO ) )
|
||||||
|
{
|
||||||
|
ulAdvertise = phyADVERTISE_ALL;
|
||||||
|
/* Reset auto-negotiation capability. */
|
||||||
|
}
|
||||||
|
else
|
||||||
|
{
|
||||||
|
/* Always select protocol 802.3u. */
|
||||||
|
ulAdvertise = phyADVERTISE_CSMA;
|
||||||
|
|
||||||
|
if( pxPhyProperties->ucSpeed == ( uint8_t )PHY_SPEED_AUTO )
|
||||||
|
{
|
||||||
|
if( pxPhyProperties->ucDuplex == ( uint8_t )PHY_DUPLEX_FULL )
|
||||||
|
{
|
||||||
|
ulAdvertise |= phyADVERTISE_10FULL | phyADVERTISE_100FULL;
|
||||||
|
}
|
||||||
|
else
|
||||||
|
{
|
||||||
|
ulAdvertise |= phyADVERTISE_10HALF | phyADVERTISE_100HALF;
|
||||||
|
}
|
||||||
|
}
|
||||||
|
else if( pxPhyProperties->ucDuplex == ( uint8_t )PHY_DUPLEX_AUTO )
|
||||||
|
{
|
||||||
|
if( pxPhyProperties->ucSpeed == ( uint8_t )PHY_SPEED_10 )
|
||||||
|
{
|
||||||
|
ulAdvertise |= phyADVERTISE_10FULL | phyADVERTISE_10HALF;
|
||||||
|
}
|
||||||
|
else
|
||||||
|
{
|
||||||
|
ulAdvertise |= phyADVERTISE_100FULL | phyADVERTISE_100HALF;
|
||||||
|
}
|
||||||
|
}
|
||||||
|
else if( pxPhyProperties->ucSpeed == ( uint8_t )PHY_SPEED_100 )
|
||||||
|
{
|
||||||
|
if( pxPhyProperties->ucDuplex == ( uint8_t )PHY_DUPLEX_FULL )
|
||||||
|
{
|
||||||
|
ulAdvertise |= phyADVERTISE_100FULL;
|
||||||
|
}
|
||||||
|
else
|
||||||
|
{
|
||||||
|
ulAdvertise |= phyADVERTISE_100HALF;
|
||||||
|
}
|
||||||
|
}
|
||||||
|
else
|
||||||
|
{
|
||||||
|
if( pxPhyProperties->ucDuplex == ( uint8_t )PHY_DUPLEX_FULL )
|
||||||
|
{
|
||||||
|
ulAdvertise |= phyADVERTISE_10FULL;
|
||||||
|
}
|
||||||
|
else
|
||||||
|
{
|
||||||
|
ulAdvertise |= phyADVERTISE_10HALF;
|
||||||
|
}
|
||||||
|
}
|
||||||
|
}
|
||||||
|
|
||||||
|
/* Send a reset command to a set of PHY-ports. */
|
||||||
|
xPhyReset( pxPhyObject, xPhyGetMask( pxPhyObject ) );
|
||||||
|
|
||||||
|
for( xPhyIndex = 0; xPhyIndex < pxPhyObject->xPortCount; xPhyIndex++ )
|
||||||
|
{
|
||||||
|
BaseType_t xPhyAddress = pxPhyObject->ucPhyIndexes[ xPhyIndex ];
|
||||||
|
uint32_t ulPhyID = pxPhyObject->ulPhyIDs[ xPhyIndex ];
|
||||||
|
|
||||||
|
/* Write advertise register. */
|
||||||
|
pxPhyObject->fnPhyWrite( xPhyAddress, phyREG_04_ADVERTISE, ulAdvertise );
|
||||||
|
|
||||||
|
/*
|
||||||
|
AN_EN AN1 AN0 Forced Mode
|
||||||
|
0 0 0 10BASE-T, Half-Duplex
|
||||||
|
0 0 1 10BASE-T, Full-Duplex
|
||||||
|
0 1 0 100BASE-TX, Half-Duplex
|
||||||
|
0 1 1 100BASE-TX, Full-Duplex
|
||||||
|
AN_EN AN1 AN0 Advertised Mode
|
||||||
|
1 0 0 10BASE-T, Half/Full-Duplex
|
||||||
|
1 0 1 100BASE-TX, Half/Full-Duplex
|
||||||
|
1 1 0 10BASE-T Half-Duplex
|
||||||
|
100BASE-TX, Half-Duplex
|
||||||
|
1 1 1 10BASE-T, Half/Full-Duplex
|
||||||
|
100BASE-TX, Half/Full-Duplex
|
||||||
|
*/
|
||||||
|
|
||||||
|
/* Read Control register. */
|
||||||
|
pxPhyObject->fnPhyRead( xPhyAddress, phyREG_00_BMCR, &ulConfig );
|
||||||
|
|
||||||
|
ulConfig &= ~( phyBMCR_SPEED_100 | phyBMCR_FULL_DUPLEX );
|
||||||
|
|
||||||
|
ulConfig |= phyBMCR_AN_ENABLE;
|
||||||
|
|
||||||
|
if( ( pxPhyProperties->ucSpeed == ( uint8_t )PHY_SPEED_100 ) || ( pxPhyProperties->ucSpeed == ( uint8_t )PHY_SPEED_AUTO ) )
|
||||||
|
{
|
||||||
|
ulConfig |= phyBMCR_SPEED_100;
|
||||||
|
}
|
||||||
|
else if( pxPhyProperties->ucSpeed == ( uint8_t )PHY_SPEED_10 )
|
||||||
|
{
|
||||||
|
ulConfig &= ~phyBMCR_SPEED_100;
|
||||||
|
}
|
||||||
|
|
||||||
|
if( ( pxPhyProperties->ucDuplex == ( uint8_t )PHY_DUPLEX_FULL ) || ( pxPhyProperties->ucDuplex == ( uint8_t )PHY_DUPLEX_AUTO ) )
|
||||||
|
{
|
||||||
|
ulConfig |= phyBMCR_FULL_DUPLEX;
|
||||||
|
}
|
||||||
|
else if( pxPhyProperties->ucDuplex == ( uint8_t )PHY_DUPLEX_HALF )
|
||||||
|
{
|
||||||
|
ulConfig &= ~phyBMCR_FULL_DUPLEX;
|
||||||
|
}
|
||||||
|
|
||||||
|
if( xHas_19_PHYCR( ulPhyID ) )
|
||||||
|
{
|
||||||
|
uint32_t ulPhyControl;
|
||||||
|
/* Read PHY Control register. */
|
||||||
|
pxPhyObject->fnPhyRead( xPhyAddress, phyREG_19_PHYCR, &ulPhyControl );
|
||||||
|
|
||||||
|
/* Clear bits which might get set: */
|
||||||
|
ulPhyControl &= ~( PHYCR_MDIX_EN|PHYCR_MDIX_FORCE );
|
||||||
|
|
||||||
|
if( pxPhyProperties->ucMDI_X == PHY_MDIX_AUTO )
|
||||||
|
{
|
||||||
|
ulPhyControl |= PHYCR_MDIX_EN;
|
||||||
|
}
|
||||||
|
else if( pxPhyProperties->ucMDI_X == PHY_MDIX_CROSSED )
|
||||||
|
{
|
||||||
|
/* Force direct link = Use crossed RJ45 cable. */
|
||||||
|
ulPhyControl &= ~PHYCR_MDIX_FORCE;
|
||||||
|
}
|
||||||
|
else
|
||||||
|
{
|
||||||
|
/* Force crossed link = Use direct RJ45 cable. */
|
||||||
|
ulPhyControl |= PHYCR_MDIX_FORCE;
|
||||||
|
}
|
||||||
|
/* update PHY Control Register. */
|
||||||
|
pxPhyObject->fnPhyWrite( xPhyAddress, phyREG_19_PHYCR, ulPhyControl );
|
||||||
|
}
|
||||||
|
|
||||||
|
FreeRTOS_printf( ( "+TCP: advertise: %04lX config %04lX\n", ulAdvertise, ulConfig ) );
|
||||||
|
}
|
||||||
|
|
||||||
|
/* Keep these values for later use. */
|
||||||
|
pxPhyObject->ulBCRValue = ulConfig & ~phyBMCR_ISOLATE;
|
||||||
|
pxPhyObject->ulACRValue = ulAdvertise;
|
||||||
|
|
||||||
|
return 0;
|
||||||
|
}
|
||||||
|
/*-----------------------------------------------------------*/
|
||||||
|
|
||||||
|
/* xPhyFixedValue(): this function is called in case auto-negotiation is disabled.
|
||||||
|
The caller has set the values in 'xPhyPreferences' (ucDuplex and ucSpeed).
|
||||||
|
The PHY register phyREG_00_BMCR will be set for every connected PHY that matches
|
||||||
|
with ulPhyMask. */
|
||||||
|
BaseType_t xPhyFixedValue( EthernetPhy_t *pxPhyObject, uint32_t ulPhyMask )
|
||||||
|
{
|
||||||
|
BaseType_t xPhyIndex;
|
||||||
|
uint32_t ulValue, ulBitMask = ( uint32_t )1u;
|
||||||
|
|
||||||
|
ulValue = ( uint32_t )0u;
|
||||||
|
|
||||||
|
if( pxPhyObject->xPhyPreferences.ucDuplex == PHY_DUPLEX_FULL )
|
||||||
|
{
|
||||||
|
ulValue |= phyBMCR_FULL_DUPLEX;
|
||||||
|
}
|
||||||
|
if( pxPhyObject->xPhyPreferences.ucSpeed == PHY_SPEED_100 )
|
||||||
|
{
|
||||||
|
ulValue |= phyBMCR_SPEED_100;
|
||||||
|
}
|
||||||
|
|
||||||
|
for( xPhyIndex = 0; xPhyIndex < pxPhyObject->xPortCount; xPhyIndex++, ulBitMask <<= 1 )
|
||||||
|
{
|
||||||
|
if( ( ulPhyMask & ulBitMask ) != 0lu )
|
||||||
|
{
|
||||||
|
BaseType_t xPhyAddress = pxPhyObject->ucPhyIndexes[ xPhyIndex ];
|
||||||
|
|
||||||
|
/* Enable Auto-Negotiation. */
|
||||||
|
pxPhyObject->fnPhyWrite( xPhyAddress, phyREG_00_BMCR, ulValue );
|
||||||
|
}
|
||||||
|
}
|
||||||
|
return 0;
|
||||||
|
}
|
||||||
|
/*-----------------------------------------------------------*/
|
||||||
|
|
||||||
|
/* xPhyStartAutoNegotiation() is the alternative xPhyFixedValue():
|
||||||
|
It sets the BMCR_AN_RESTART bit and waits for the auto-negotiation completion
|
||||||
|
( phyBMSR_AN_COMPLETE ). */
|
||||||
|
BaseType_t xPhyStartAutoNegotiation( EthernetPhy_t *pxPhyObject, uint32_t ulPhyMask )
|
||||||
|
{
|
||||||
|
uint32_t xPhyIndex, ulDoneMask, ulBitMask;
|
||||||
|
uint32_t ulPHYLinkStatus, ulRegValue;
|
||||||
|
TickType_t xRemainingTime;
|
||||||
|
TimeOut_t xTimer;
|
||||||
|
|
||||||
|
if( ulPhyMask == ( uint32_t )0u )
|
||||||
|
{
|
||||||
|
return 0;
|
||||||
|
}
|
||||||
|
for( xPhyIndex = 0; xPhyIndex < ( uint32_t ) pxPhyObject->xPortCount; xPhyIndex++ )
|
||||||
|
{
|
||||||
|
if( ( ulPhyMask & ( 1lu << xPhyIndex ) ) != 0lu )
|
||||||
|
{
|
||||||
|
BaseType_t xPhyAddress = pxPhyObject->ucPhyIndexes[ xPhyIndex ];
|
||||||
|
|
||||||
|
/* Enable Auto-Negotiation. */
|
||||||
|
pxPhyObject->fnPhyWrite( xPhyAddress, phyREG_04_ADVERTISE, pxPhyObject->ulACRValue);
|
||||||
|
pxPhyObject->fnPhyWrite( xPhyAddress, phyREG_00_BMCR, pxPhyObject->ulBCRValue | phyBMCR_AN_RESTART );
|
||||||
|
}
|
||||||
|
}
|
||||||
|
xRemainingTime = ( TickType_t ) pdMS_TO_TICKS( phyPHY_MAX_NEGOTIATE_TIME_MS );
|
||||||
|
vTaskSetTimeOutState( &xTimer );
|
||||||
|
ulDoneMask = 0;
|
||||||
|
/* Wait until the auto-negotiation will be completed */
|
||||||
|
for( ;; )
|
||||||
|
{
|
||||||
|
ulBitMask = ( uint32_t )1u;
|
||||||
|
for( xPhyIndex = 0; xPhyIndex < ( uint32_t ) pxPhyObject->xPortCount; xPhyIndex++, ulBitMask <<= 1 )
|
||||||
|
{
|
||||||
|
if( ( ulPhyMask & ulBitMask ) != 0lu )
|
||||||
|
{
|
||||||
|
if( ( ulDoneMask & ulBitMask ) == 0lu )
|
||||||
|
{
|
||||||
|
BaseType_t xPhyAddress = pxPhyObject->ucPhyIndexes[ xPhyIndex ];
|
||||||
|
|
||||||
|
pxPhyObject->fnPhyRead( xPhyAddress, phyREG_01_BMSR, &ulRegValue );
|
||||||
|
if( ( ulRegValue & phyBMSR_AN_COMPLETE ) != 0 )
|
||||||
|
{
|
||||||
|
ulDoneMask |= ulBitMask;
|
||||||
|
}
|
||||||
|
}
|
||||||
|
}
|
||||||
|
}
|
||||||
|
if( ulPhyMask == ulDoneMask )
|
||||||
|
{
|
||||||
|
break;
|
||||||
|
}
|
||||||
|
if( xTaskCheckForTimeOut( &xTimer, &xRemainingTime ) != pdFALSE )
|
||||||
|
{
|
||||||
|
FreeRTOS_printf( ( "xPhyStartAutoNegotiation: phyBMCR_RESET timed out ( done 0x%02lX )\n", ulDoneMask ) );
|
||||||
|
break;
|
||||||
|
}
|
||||||
|
vTaskDelay( pdMS_TO_TICKS( phySHORT_DELAY_MS ) );
|
||||||
|
}
|
||||||
|
|
||||||
|
if( ulDoneMask != ( uint32_t)0u )
|
||||||
|
{
|
||||||
|
ulBitMask = ( uint32_t )1u;
|
||||||
|
pxPhyObject->ulLinkStatusMask &= ~( ulDoneMask );
|
||||||
|
for( xPhyIndex = 0; xPhyIndex < ( uint32_t ) pxPhyObject->xPortCount; xPhyIndex++, ulBitMask <<= 1 )
|
||||||
|
{
|
||||||
|
BaseType_t xPhyAddress = pxPhyObject->ucPhyIndexes[ xPhyIndex ];
|
||||||
|
uint32_t ulPhyID = pxPhyObject->ulPhyIDs[ xPhyIndex ];
|
||||||
|
|
||||||
|
if( ( ulDoneMask & ulBitMask ) == ( uint32_t )0u )
|
||||||
|
{
|
||||||
|
continue;
|
||||||
|
}
|
||||||
|
|
||||||
|
/* Clear the 'phyBMCR_AN_RESTART' bit. */
|
||||||
|
pxPhyObject->fnPhyWrite( xPhyAddress, phyREG_00_BMCR, pxPhyObject->ulBCRValue );
|
||||||
|
|
||||||
|
pxPhyObject->fnPhyRead( xPhyAddress, phyREG_01_BMSR, &ulRegValue);
|
||||||
|
if( ( ulRegValue & phyBMSR_LINK_STATUS ) != 0 )
|
||||||
|
{
|
||||||
|
ulPHYLinkStatus |= phyBMSR_LINK_STATUS;
|
||||||
|
pxPhyObject->ulLinkStatusMask |= ulBitMask;
|
||||||
|
}
|
||||||
|
else
|
||||||
|
{
|
||||||
|
ulPHYLinkStatus &= ~( phyBMSR_LINK_STATUS );
|
||||||
|
}
|
||||||
|
|
||||||
|
if( ulPhyID == PHY_ID_KSZ8081MNXIA )
|
||||||
|
{
|
||||||
|
uint32_t ulControlStatus;
|
||||||
|
|
||||||
|
pxPhyObject->fnPhyRead( xPhyAddress, 0x1E, &ulControlStatus);
|
||||||
|
switch( ulControlStatus & 0x07 )
|
||||||
|
{
|
||||||
|
case 0x01:
|
||||||
|
case 0x05:
|
||||||
|
// [001] = 10BASE-T half-duplex
|
||||||
|
// [101] = 10BASE-T full-duplex
|
||||||
|
/* 10 Mbps. */
|
||||||
|
ulRegValue |= phyPHYSTS_SPEED_STATUS;
|
||||||
|
break;
|
||||||
|
case 0x02:
|
||||||
|
case 0x06:
|
||||||
|
// [010] = 100BASE-TX half-duplex
|
||||||
|
// [110] = 100BASE-TX full-duplex
|
||||||
|
break;
|
||||||
|
}
|
||||||
|
switch( ulControlStatus & 0x07 )
|
||||||
|
{
|
||||||
|
case 0x05:
|
||||||
|
case 0x06:
|
||||||
|
// [101] = 10BASE-T full-duplex
|
||||||
|
// [110] = 100BASE-TX full-duplex
|
||||||
|
/* Full duplex. */
|
||||||
|
ulRegValue |= phyPHYSTS_DUPLEX_STATUS;
|
||||||
|
break;
|
||||||
|
case 0x01:
|
||||||
|
case 0x02:
|
||||||
|
// [001] = 10BASE-T half-duplex
|
||||||
|
// [010] = 100BASE-TX half-duplex
|
||||||
|
break;
|
||||||
|
}
|
||||||
|
}
|
||||||
|
else if( xHas_1F_PHYSPCS( ulPhyID ) )
|
||||||
|
{
|
||||||
|
/* 31 RW PHY Special Control Status */
|
||||||
|
uint32_t ulControlStatus;
|
||||||
|
|
||||||
|
pxPhyObject->fnPhyRead( xPhyAddress, phyREG_1F_PHYSPCS, &ulControlStatus);
|
||||||
|
ulRegValue = 0;
|
||||||
|
if( ( ulControlStatus & phyPHYSPCS_FULL_DUPLEX ) != 0 )
|
||||||
|
{
|
||||||
|
ulRegValue |= phyPHYSTS_DUPLEX_STATUS;
|
||||||
|
}
|
||||||
|
if( ( ulControlStatus & phyPHYSPCS_SPEED_MASK ) == phyPHYSPCS_SPEED_10 )
|
||||||
|
{
|
||||||
|
ulRegValue |= phyPHYSTS_SPEED_STATUS;
|
||||||
|
}
|
||||||
|
}
|
||||||
|
else
|
||||||
|
{
|
||||||
|
/* Read the result of the auto-negotiation. */
|
||||||
|
pxPhyObject->fnPhyRead( xPhyAddress, PHYREG_10_PHYSTS, &ulRegValue);
|
||||||
|
}
|
||||||
|
|
||||||
|
FreeRTOS_printf( ( "Autonego ready: %08lx: %s duplex %u mbit %s status\n",
|
||||||
|
ulRegValue,
|
||||||
|
( ulRegValue & phyPHYSTS_DUPLEX_STATUS ) ? "full" : "half",
|
||||||
|
( ulRegValue & phyPHYSTS_SPEED_STATUS ) ? 10 : 100,
|
||||||
|
( ( ulPHYLinkStatus |= phyBMSR_LINK_STATUS ) != 0) ? "high" : "low" ) );
|
||||||
|
if( ( ulRegValue & phyPHYSTS_DUPLEX_STATUS ) != ( uint32_t )0u )
|
||||||
|
{
|
||||||
|
pxPhyObject->xPhyProperties.ucDuplex = PHY_DUPLEX_FULL;
|
||||||
|
}
|
||||||
|
else
|
||||||
|
{
|
||||||
|
pxPhyObject->xPhyProperties.ucDuplex = PHY_DUPLEX_HALF;
|
||||||
|
}
|
||||||
|
|
||||||
|
if( ( ulRegValue & phyPHYSTS_SPEED_STATUS ) != 0 )
|
||||||
|
{
|
||||||
|
pxPhyObject->xPhyProperties.ucSpeed = PHY_SPEED_10;
|
||||||
|
}
|
||||||
|
else
|
||||||
|
{
|
||||||
|
pxPhyObject->xPhyProperties.ucSpeed = PHY_SPEED_100;
|
||||||
|
}
|
||||||
|
}
|
||||||
|
} /* if( ulDoneMask != ( uint32_t)0u ) */
|
||||||
|
|
||||||
|
return 0;
|
||||||
|
}
|
||||||
|
/*-----------------------------------------------------------*/
|
||||||
|
|
||||||
|
BaseType_t xPhyCheckLinkStatus( EthernetPhy_t *pxPhyObject, BaseType_t xHadReception )
|
||||||
|
{
|
||||||
|
uint32_t ulStatus, ulBitMask = 1u;
|
||||||
|
BaseType_t xPhyIndex;
|
||||||
|
BaseType_t xNeedCheck = pdFALSE;
|
||||||
|
|
||||||
|
if( xHadReception > 0 )
|
||||||
|
{
|
||||||
|
/* A packet was received. No need to check for the PHY status now,
|
||||||
|
but set a timer to check it later on. */
|
||||||
|
vTaskSetTimeOutState( &( pxPhyObject->xLinkStatusTimer ) );
|
||||||
|
pxPhyObject->xLinkStatusRemaining = pdMS_TO_TICKS( ipconfigPHY_LS_HIGH_CHECK_TIME_MS );
|
||||||
|
for( xPhyIndex = 0; xPhyIndex < pxPhyObject->xPortCount; xPhyIndex++, ulBitMask <<= 1 )
|
||||||
|
{
|
||||||
|
if( ( pxPhyObject->ulLinkStatusMask & ulBitMask ) == 0ul )
|
||||||
|
{
|
||||||
|
pxPhyObject->ulLinkStatusMask |= ulBitMask;
|
||||||
|
FreeRTOS_printf( ( "xPhyCheckLinkStatus: PHY LS now %02lX\n", pxPhyObject->ulLinkStatusMask ) );
|
||||||
|
xNeedCheck = pdTRUE;
|
||||||
|
}
|
||||||
|
}
|
||||||
|
}
|
||||||
|
else if( xTaskCheckForTimeOut( &( pxPhyObject->xLinkStatusTimer ), &( pxPhyObject->xLinkStatusRemaining ) ) != pdFALSE )
|
||||||
|
{
|
||||||
|
/* Frequent checking the PHY Link Status can affect for the performance of Ethernet controller.
|
||||||
|
As long as packets are received, no polling is needed.
|
||||||
|
Otherwise, polling will be done when the 'xLinkStatusTimer' expires. */
|
||||||
|
for( xPhyIndex = 0; xPhyIndex < pxPhyObject->xPortCount; xPhyIndex++, ulBitMask <<= 1 )
|
||||||
|
{
|
||||||
|
BaseType_t xPhyAddress = pxPhyObject->ucPhyIndexes[ xPhyIndex ];
|
||||||
|
|
||||||
|
if( pxPhyObject->fnPhyRead( xPhyAddress, phyREG_01_BMSR, &ulStatus ) == 0 )
|
||||||
|
{
|
||||||
|
if( !!( pxPhyObject->ulLinkStatusMask & ulBitMask ) != !!( ulStatus & phyBMSR_LINK_STATUS ) )
|
||||||
|
{
|
||||||
|
if( ( ulStatus & phyBMSR_LINK_STATUS ) != 0 )
|
||||||
|
{
|
||||||
|
pxPhyObject->ulLinkStatusMask |= ulBitMask;
|
||||||
|
}
|
||||||
|
else
|
||||||
|
{
|
||||||
|
pxPhyObject->ulLinkStatusMask &= ~( ulBitMask );
|
||||||
|
}
|
||||||
|
FreeRTOS_printf( ( "xPhyCheckLinkStatus: PHY LS now %02lX\n", pxPhyObject->ulLinkStatusMask ) );
|
||||||
|
xNeedCheck = pdTRUE;
|
||||||
|
}
|
||||||
|
}
|
||||||
|
}
|
||||||
|
vTaskSetTimeOutState( &( pxPhyObject->xLinkStatusTimer ) );
|
||||||
|
if( ( pxPhyObject->ulLinkStatusMask & phyBMSR_LINK_STATUS ) != 0 )
|
||||||
|
{
|
||||||
|
/* The link status is high, so don't poll the PHY too often. */
|
||||||
|
pxPhyObject->xLinkStatusRemaining = pdMS_TO_TICKS( ipconfigPHY_LS_HIGH_CHECK_TIME_MS );
|
||||||
|
}
|
||||||
|
else
|
||||||
|
{
|
||||||
|
/* The link status is low, polling may be done more frequently. */
|
||||||
|
pxPhyObject->xLinkStatusRemaining = pdMS_TO_TICKS( ipconfigPHY_LS_LOW_CHECK_TIME_MS );
|
||||||
|
}
|
||||||
|
}
|
||||||
|
return xNeedCheck;
|
||||||
|
}
|
||||||
|
/*-----------------------------------------------------------*/
|
||||||
File diff suppressed because it is too large
Load Diff
File diff suppressed because it is too large
Load Diff
File diff suppressed because it is too large
Load Diff
@ -0,0 +1,6 @@
|
|||||||
|
/*
|
||||||
|
* The Ethernet header files for STM32F2, STM32F4 and STM32F7 have been merged to
|
||||||
|
* a single module that works for both parts: "stm32fxx_hal_eth"
|
||||||
|
*/
|
||||||
|
|
||||||
|
#include "stm32fxx_hal_eth.h"
|
||||||
File diff suppressed because it is too large
Load Diff
@ -0,0 +1,6 @@
|
|||||||
|
/*
|
||||||
|
* The Ethernet header files for STM32F2, STM32F4 and STM32F7 have been merged to
|
||||||
|
* a single module that works for both parts: "stm32fxx_hal_eth"
|
||||||
|
*/
|
||||||
|
|
||||||
|
#include "stm32fxx_hal_eth.h"
|
||||||
@ -0,0 +1,6 @@
|
|||||||
|
/*
|
||||||
|
* The Ethernet header files for STM32F2, STM32F4 and STM32F7 have been merged to
|
||||||
|
* a single module that works for both parts: "stm32fxx_hal_eth"
|
||||||
|
*/
|
||||||
|
|
||||||
|
#include "stm32fxx_hal_eth.h"
|
||||||
File diff suppressed because it is too large
Load Diff
File diff suppressed because it is too large
Load Diff
@ -0,0 +1,132 @@
|
|||||||
|
/*
|
||||||
|
* uncached_memory.c
|
||||||
|
*
|
||||||
|
* This module will declare 1 MB of memory and switch off the caching for it.
|
||||||
|
*
|
||||||
|
* pucGetUncachedMemory( ulSize ) returns a trunc of this memory with a length
|
||||||
|
* rounded up to a multiple of 4 KB
|
||||||
|
*
|
||||||
|
* ucIsCachedMemory( pucBuffer ) returns non-zero if a given pointer is NOT
|
||||||
|
* within the range of the 1 MB non-cached memory.
|
||||||
|
*
|
||||||
|
*/
|
||||||
|
|
||||||
|
/*
|
||||||
|
* After "_end", 1 MB of uncached memory will be allocated for DMA transfers.
|
||||||
|
* Both the DMA descriptors as well as all EMAC TX-buffers will be allocated in
|
||||||
|
* uncached memory.
|
||||||
|
*/
|
||||||
|
|
||||||
|
/* Standard includes. */
|
||||||
|
#include <stdint.h>
|
||||||
|
#include <stdio.h>
|
||||||
|
#include <stdlib.h>
|
||||||
|
|
||||||
|
/* FreeRTOS includes. */
|
||||||
|
#include "FreeRTOS.h"
|
||||||
|
#include "task.h"
|
||||||
|
#include "queue.h"
|
||||||
|
|
||||||
|
/* FreeRTOS+TCP includes. */
|
||||||
|
#include "FreeRTOS_IP.h"
|
||||||
|
#include "FreeRTOS_Sockets.h"
|
||||||
|
#include "FreeRTOS_IP_Private.h"
|
||||||
|
|
||||||
|
#include "Zynq/x_emacpsif.h"
|
||||||
|
#include "Zynq/x_topology.h"
|
||||||
|
#include "xstatus.h"
|
||||||
|
|
||||||
|
#include "xparameters.h"
|
||||||
|
#include "xparameters_ps.h"
|
||||||
|
#include "xil_exception.h"
|
||||||
|
#include "xil_mmu.h"
|
||||||
|
|
||||||
|
#include "uncached_memory.h"
|
||||||
|
|
||||||
|
#define UNCACHED_MEMORY_SIZE 0x100000ul
|
||||||
|
|
||||||
|
#define DDR_MEMORY_END (XPAR_PS7_DDR_0_S_AXI_HIGHADDR+1)
|
||||||
|
|
||||||
|
static void vInitialiseUncachedMemory( void );
|
||||||
|
|
||||||
|
static uint8_t *pucHeadOfMemory;
|
||||||
|
static uint32_t ulMemorySize;
|
||||||
|
static uint8_t *pucStartOfMemory = NULL;
|
||||||
|
|
||||||
|
uint8_t ucIsCachedMemory( const uint8_t *pucBuffer )
|
||||||
|
{
|
||||||
|
uint8_t ucReturn;
|
||||||
|
|
||||||
|
if( ( pucStartOfMemory != NULL ) &&
|
||||||
|
( pucBuffer >= pucStartOfMemory ) &&
|
||||||
|
( pucBuffer < ( pucStartOfMemory + UNCACHED_MEMORY_SIZE ) ) )
|
||||||
|
{
|
||||||
|
ucReturn = pdFALSE;
|
||||||
|
}
|
||||||
|
else
|
||||||
|
{
|
||||||
|
ucReturn = pdTRUE;
|
||||||
|
}
|
||||||
|
|
||||||
|
return ucReturn;
|
||||||
|
}
|
||||||
|
|
||||||
|
uint8_t *pucGetUncachedMemory( uint32_t ulSize )
|
||||||
|
{
|
||||||
|
uint8_t *pucReturn;
|
||||||
|
|
||||||
|
if( pucStartOfMemory == NULL )
|
||||||
|
{
|
||||||
|
vInitialiseUncachedMemory( );
|
||||||
|
}
|
||||||
|
if( ( pucStartOfMemory == NULL ) || ( ulSize > ulMemorySize ) )
|
||||||
|
{
|
||||||
|
pucReturn = NULL;
|
||||||
|
}
|
||||||
|
else
|
||||||
|
{
|
||||||
|
uint32_t ulSkipSize;
|
||||||
|
|
||||||
|
pucReturn = pucHeadOfMemory;
|
||||||
|
ulSkipSize = ( ulSize + 0x1000ul ) & ~0xffful;
|
||||||
|
pucHeadOfMemory += ulSkipSize;
|
||||||
|
ulMemorySize -= ulSkipSize;
|
||||||
|
}
|
||||||
|
|
||||||
|
return pucReturn;
|
||||||
|
}
|
||||||
|
|
||||||
|
extern u8 _end;
|
||||||
|
|
||||||
|
static void vInitialiseUncachedMemory( )
|
||||||
|
{
|
||||||
|
/* At the end of program's space... */
|
||||||
|
pucStartOfMemory = (uint8_t *) &_end;
|
||||||
|
/*
|
||||||
|
* Align the start address to 1 MB boundary.
|
||||||
|
*/
|
||||||
|
pucStartOfMemory = (uint8_t *)( ( ( uint32_t )pucStartOfMemory + UNCACHED_MEMORY_SIZE ) & ( ~( UNCACHED_MEMORY_SIZE - 1 ) ) );
|
||||||
|
|
||||||
|
if( ( ( u32 )pucStartOfMemory ) + UNCACHED_MEMORY_SIZE > DDR_MEMORY_END )
|
||||||
|
{
|
||||||
|
// vLoggingPrintf("vInitialiseUncachedMemory: Can not allocate uncached memory\n" );
|
||||||
|
}
|
||||||
|
else
|
||||||
|
{
|
||||||
|
/*
|
||||||
|
* Some objects want to be stored in uncached memory. Hence the 1 MB
|
||||||
|
* address range that starts after "_end" is made uncached
|
||||||
|
* by setting appropriate attributes in the translation table.
|
||||||
|
*/
|
||||||
|
/* FIXME claudio rossi. Modified to prevent data abort exception (misaligned access)
|
||||||
|
* when application is compiled with -O1 or more optimization flag.
|
||||||
|
*/
|
||||||
|
/* Xil_SetTlbAttributes( ( uint32_t )pucStartOfMemory, 0xc02 ); // addr, attr */
|
||||||
|
Xil_SetTlbAttributes( ( uint32_t )pucStartOfMemory, 0x1c02 ); // addr, attr
|
||||||
|
|
||||||
|
/* For experiments in the SDIO driver, make the remaining uncached memory public */
|
||||||
|
pucHeadOfMemory = pucStartOfMemory;
|
||||||
|
ulMemorySize = UNCACHED_MEMORY_SIZE;
|
||||||
|
memset( pucStartOfMemory, '\0', UNCACHED_MEMORY_SIZE );
|
||||||
|
}
|
||||||
|
}
|
||||||
@ -0,0 +1,23 @@
|
|||||||
|
/*
|
||||||
|
* uncached_memory.h
|
||||||
|
*
|
||||||
|
* This module will declare 1 MB of memory and switch off the caching for it.
|
||||||
|
*
|
||||||
|
* pucGetUncachedMemory( ulSize ) returns a trunc of this memory with a length
|
||||||
|
* rounded up to a multiple of 4 KB
|
||||||
|
*
|
||||||
|
* ucIsCachedMemory( pucBuffer ) returns non-zero if a given pointer is NOT
|
||||||
|
* within the range of the 1 MB non-cached memory.
|
||||||
|
*
|
||||||
|
*/
|
||||||
|
|
||||||
|
#ifndef UNCACHEMEMORY_H
|
||||||
|
|
||||||
|
#define UNCACHEMEMORY_H
|
||||||
|
|
||||||
|
uint8_t *pucGetUncachedMemory( uint32_t ulSize );
|
||||||
|
|
||||||
|
uint8_t ucIsCachedMemory( const uint8_t *pucBuffer );
|
||||||
|
|
||||||
|
#endif /* UNCACHEMEMORY_H */
|
||||||
|
|
||||||
@ -0,0 +1,118 @@
|
|||||||
|
/*
|
||||||
|
* Handling of Ethernet PHY's
|
||||||
|
* PHY's communicate with an EMAC either through
|
||||||
|
* a Media-Independent Interface (MII), or a Reduced Media-Independent Interface (RMII).
|
||||||
|
* The EMAC can poll for PHY ports on 32 different addresses. Each of the PHY ports
|
||||||
|
* shall be treated independently.
|
||||||
|
*
|
||||||
|
*/
|
||||||
|
|
||||||
|
#ifndef PHYHANDLING_H
|
||||||
|
|
||||||
|
#define PHYHANDLING_H
|
||||||
|
|
||||||
|
#ifdef __cplusplus
|
||||||
|
extern "C" {
|
||||||
|
#endif
|
||||||
|
|
||||||
|
|
||||||
|
#ifndef ipconfigPHY_MAX_PORTS
|
||||||
|
/* There can be at most 32 PHY ports, but in most cases there are 4 or less. */
|
||||||
|
#define ipconfigPHY_MAX_PORTS 4
|
||||||
|
#endif
|
||||||
|
|
||||||
|
/* A generic user-provided function that reads from the PHY-port at 'xAddress'( 0-based ). A 16-bit value shall be stored in
|
||||||
|
'*pulValue'. xRegister is the register number ( 0 .. 31 ). In fact all PHY registers are 16-bit.
|
||||||
|
Return non-zero in case the action failed. */
|
||||||
|
typedef BaseType_t ( *xApplicationPhyReadHook_t )( BaseType_t xAddress, BaseType_t xRegister, uint32_t *pulValue );
|
||||||
|
|
||||||
|
/* A generic user-provided function that writes 'ulValue' to the
|
||||||
|
PHY-port at 'xAddress' ( 0-based ). xRegister is the register number ( 0 .. 31 ).
|
||||||
|
Return non-zero in case the action failed. */
|
||||||
|
typedef BaseType_t ( *xApplicationPhyWriteHook_t )( BaseType_t xAddress, BaseType_t xRegister, uint32_t ulValue );
|
||||||
|
|
||||||
|
typedef struct xPhyProperties
|
||||||
|
{
|
||||||
|
uint8_t ucSpeed;
|
||||||
|
uint8_t ucMDI_X; /* MDI-X : Medium Dependent Interface - Crossover */
|
||||||
|
uint8_t ucDuplex;
|
||||||
|
uint8_t ucSpare;
|
||||||
|
} PhyProperties_t;
|
||||||
|
|
||||||
|
typedef struct xEthernetPhy
|
||||||
|
{
|
||||||
|
xApplicationPhyReadHook_t fnPhyRead;
|
||||||
|
xApplicationPhyWriteHook_t fnPhyWrite;
|
||||||
|
uint32_t ulPhyIDs[ ipconfigPHY_MAX_PORTS ];
|
||||||
|
uint8_t ucPhyIndexes[ ipconfigPHY_MAX_PORTS ];
|
||||||
|
TimeOut_t xLinkStatusTimer;
|
||||||
|
TickType_t xLinkStatusRemaining;
|
||||||
|
BaseType_t xPortCount;
|
||||||
|
uint32_t ulBCRValue;
|
||||||
|
uint32_t ulACRValue;
|
||||||
|
uint32_t ulLinkStatusMask;
|
||||||
|
PhyProperties_t xPhyPreferences;
|
||||||
|
PhyProperties_t xPhyProperties;
|
||||||
|
} EthernetPhy_t;
|
||||||
|
|
||||||
|
/* Some defines used internally here to indicate preferences about speed, MDIX
|
||||||
|
(wired direct or crossed), and duplex (half or full). */
|
||||||
|
|
||||||
|
/* Values for PhyProperties_t::ucSpeed : */
|
||||||
|
#define PHY_SPEED_10 1
|
||||||
|
#define PHY_SPEED_100 2
|
||||||
|
#define PHY_SPEED_AUTO 3
|
||||||
|
|
||||||
|
/* Values for PhyProperties_t::ucMDI_X : */
|
||||||
|
#define PHY_MDIX_DIRECT 1
|
||||||
|
#define PHY_MDIX_CROSSED 2
|
||||||
|
#define PHY_MDIX_AUTO 3
|
||||||
|
|
||||||
|
/* Values for PhyProperties_t::ucDuplex : */
|
||||||
|
#define PHY_DUPLEX_HALF 1
|
||||||
|
#define PHY_DUPLEX_FULL 2
|
||||||
|
#define PHY_DUPLEX_AUTO 3
|
||||||
|
|
||||||
|
/* ID's of supported PHY's : */
|
||||||
|
#define PHY_ID_LAN8742A 0x0007c130
|
||||||
|
#define PHY_ID_LAN8720 0x0007c0f0
|
||||||
|
|
||||||
|
#define PHY_ID_KSZ8041 0x000010A1
|
||||||
|
#define PHY_ID_KSZ8051 0x000010A1
|
||||||
|
#define PHY_ID_KSZ8081 0x000010A1
|
||||||
|
|
||||||
|
#define PHY_ID_KSZ8863 0x00221430
|
||||||
|
#define PHY_ID_KSZ8081MNXIA 0x00221560
|
||||||
|
|
||||||
|
#define PHY_ID_DP83848I 0x20005C90
|
||||||
|
|
||||||
|
|
||||||
|
/* Initialise the struct and assign a PHY-read and -write function. */
|
||||||
|
void vPhyInitialise( EthernetPhy_t *pxPhyObject, xApplicationPhyReadHook_t fnPhyRead, xApplicationPhyWriteHook_t fnPhyWrite );
|
||||||
|
|
||||||
|
/* Discover all PHY's connected by polling 32 indexes ( zero-based ) */
|
||||||
|
BaseType_t xPhyDiscover( EthernetPhy_t *pxPhyObject );
|
||||||
|
|
||||||
|
/* Send a reset command to the connected PHY ports and send configuration. */
|
||||||
|
BaseType_t xPhyConfigure( EthernetPhy_t *pxPhyObject, const PhyProperties_t *pxPhyProperties );
|
||||||
|
|
||||||
|
/* Give a command to start auto negotiation on a set of PHY port's. */
|
||||||
|
BaseType_t xPhyStartAutoNegotiation( EthernetPhy_t *pxPhyObject, uint32_t ulPhyMask );
|
||||||
|
|
||||||
|
/* Do not use auto negotiation but use predefined values from 'pxPhyObject->xPhyPreferences'. */
|
||||||
|
BaseType_t xPhyFixedValue( EthernetPhy_t *pxPhyObject, uint32_t ulPhyMask );
|
||||||
|
|
||||||
|
/* Check the current Link Status.
|
||||||
|
'xHadReception' : make this true if a packet has been received since the
|
||||||
|
last call to this function. */
|
||||||
|
BaseType_t xPhyCheckLinkStatus( EthernetPhy_t *pxPhyObject, BaseType_t xHadReception );
|
||||||
|
|
||||||
|
/* Get the bitmask of a given 'EthernetPhy_t'. */
|
||||||
|
#define xPhyGetMask( pxPhyObject ) \
|
||||||
|
( ( ( ( uint32_t ) 1u ) << ( pxPhyObject )->xPortCount ) - 1u )
|
||||||
|
|
||||||
|
#ifdef __cplusplus
|
||||||
|
} /* extern "C" */
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#endif
|
||||||
@ -0,0 +1,610 @@
|
|||||||
|
/**
|
||||||
|
*
|
||||||
|
* \file
|
||||||
|
*
|
||||||
|
* \brief KS8851SNL driver for SAM.
|
||||||
|
*
|
||||||
|
* Copyright (c) 2013-2015 Atmel Corporation. All rights reserved.
|
||||||
|
*
|
||||||
|
* \asf_license_start
|
||||||
|
*
|
||||||
|
* \page License
|
||||||
|
*
|
||||||
|
* Redistribution and use in source and binary forms, with or without
|
||||||
|
* modification, are permitted provided that the following conditions are met:
|
||||||
|
*
|
||||||
|
* 1. Redistributions of source code must retain the above copyright notice,
|
||||||
|
* this list of conditions and the following disclaimer.
|
||||||
|
*
|
||||||
|
* 2. Redistributions in binary form must reproduce the above copyright notice,
|
||||||
|
* this list of conditions and the following disclaimer in the documentation
|
||||||
|
* and/or other materials provided with the distribution.
|
||||||
|
*
|
||||||
|
* 3. The name of Atmel may not be used to endorse or promote products derived
|
||||||
|
* from this software without specific prior written permission.
|
||||||
|
*
|
||||||
|
* 4. This software may only be redistributed and used in connection with an
|
||||||
|
* Atmel microcontroller product.
|
||||||
|
*
|
||||||
|
* THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
|
||||||
|
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
|
||||||
|
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
|
||||||
|
* EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
|
||||||
|
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
||||||
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
||||||
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
||||||
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
||||||
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||||
|
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||||
|
* POSSIBILITY OF SUCH DAMAGE.
|
||||||
|
*
|
||||||
|
* \asf_license_stop
|
||||||
|
*
|
||||||
|
*/
|
||||||
|
/*
|
||||||
|
* Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a>
|
||||||
|
*/
|
||||||
|
|
||||||
|
/* FreeRTOS includes. */
|
||||||
|
#include "FreeRTOS.h"
|
||||||
|
#include "task.h"
|
||||||
|
|
||||||
|
#include "spi_master.h"
|
||||||
|
#include "ksz8851snl.h"
|
||||||
|
#include "ksz8851snl_reg.h"
|
||||||
|
#include "delay.h"
|
||||||
|
#include "pio.h"
|
||||||
|
#include "pio_handler.h"
|
||||||
|
#include "pdc.h"
|
||||||
|
#include "conf_eth.h"
|
||||||
|
|
||||||
|
/* Clock polarity. */
|
||||||
|
#define SPI_CLK_POLARITY 0
|
||||||
|
|
||||||
|
/* Clock phase. */
|
||||||
|
#define SPI_CLK_PHASE 1
|
||||||
|
|
||||||
|
/* SPI PDC register base. */
|
||||||
|
Pdc *g_p_spi_pdc = 0;
|
||||||
|
|
||||||
|
int lUDPLoggingPrintf( const char *pcFormatString, ... );
|
||||||
|
|
||||||
|
/* Temporary buffer for PDC reception. */
|
||||||
|
uint8_t tmpbuf[1536] __attribute__ ((aligned (16)));
|
||||||
|
|
||||||
|
union {
|
||||||
|
uint64_t ul[2];
|
||||||
|
uint8_t uc[16];
|
||||||
|
} cmdBuf, respBuf;
|
||||||
|
|
||||||
|
void dbg_add_line( const char *pcFormat, ... );
|
||||||
|
|
||||||
|
static void spi_clear_ovres( void );
|
||||||
|
|
||||||
|
/**
|
||||||
|
* \brief Read register content, set bitmask and write back to register.
|
||||||
|
*
|
||||||
|
* \param reg the register address to modify.
|
||||||
|
* \param bits_to_set bitmask to apply.
|
||||||
|
*/
|
||||||
|
void ksz8851_reg_setbits(uint16_t reg, uint16_t bits_to_set)
|
||||||
|
{
|
||||||
|
uint16_t temp;
|
||||||
|
|
||||||
|
temp = ksz8851_reg_read(reg);
|
||||||
|
temp |= bits_to_set;
|
||||||
|
ksz8851_reg_write(reg, temp);
|
||||||
|
}
|
||||||
|
|
||||||
|
/**
|
||||||
|
* \brief Read register content, clear bitmask and write back to register.
|
||||||
|
*
|
||||||
|
* \param reg the register address to modify.
|
||||||
|
* \param bits_to_set bitmask to apply.
|
||||||
|
*/
|
||||||
|
void ksz8851_reg_clrbits(uint16_t reg, uint16_t bits_to_clr)
|
||||||
|
{
|
||||||
|
uint16_t temp;
|
||||||
|
|
||||||
|
temp = ksz8851_reg_read(reg);
|
||||||
|
temp &= ~(uint32_t) bits_to_clr;
|
||||||
|
ksz8851_reg_write(reg, temp);
|
||||||
|
}
|
||||||
|
|
||||||
|
/**
|
||||||
|
* \brief Configure the INTN interrupt.
|
||||||
|
*/
|
||||||
|
void configure_intn(void (*p_handler) (uint32_t, uint32_t))
|
||||||
|
{
|
||||||
|
// gpio_configure_pin(KSZ8851SNL_INTN_GPIO, PIO_INPUT);
|
||||||
|
// pio_set_input(PIOA, PIO_PA11_IDX, PIO_PULLUP);
|
||||||
|
|
||||||
|
/* Configure PIO clock. */
|
||||||
|
pmc_enable_periph_clk(INTN_ID);
|
||||||
|
|
||||||
|
/* Adjust PIO debounce filter parameters, uses 10 Hz filter. */
|
||||||
|
pio_set_debounce_filter(INTN_PIO, INTN_PIN_MSK, 10);
|
||||||
|
|
||||||
|
/* Initialize PIO interrupt handlers, see PIO definition in board.h. */
|
||||||
|
pio_handler_set(INTN_PIO, INTN_ID, INTN_PIN_MSK,
|
||||||
|
INTN_ATTR, p_handler);
|
||||||
|
|
||||||
|
/* Enable NVIC interrupts. */
|
||||||
|
NVIC_SetPriority(INTN_IRQn, INT_PRIORITY_PIO);
|
||||||
|
NVIC_EnableIRQ((IRQn_Type)INTN_ID);
|
||||||
|
|
||||||
|
/* Enable PIO interrupts. */
|
||||||
|
pio_enable_interrupt(INTN_PIO, INTN_PIN_MSK);
|
||||||
|
}
|
||||||
|
|
||||||
|
/**
|
||||||
|
* \brief Read a register value.
|
||||||
|
*
|
||||||
|
* \param reg the register address to modify.
|
||||||
|
*
|
||||||
|
* \return the register value.
|
||||||
|
*/
|
||||||
|
uint16_t ksz8851_reg_read(uint16_t reg)
|
||||||
|
{
|
||||||
|
pdc_packet_t g_pdc_spi_tx_packet;
|
||||||
|
pdc_packet_t g_pdc_spi_rx_packet;
|
||||||
|
uint16_t cmd = 0;
|
||||||
|
uint16_t res = 0;
|
||||||
|
int iTryCount = 3;
|
||||||
|
|
||||||
|
while( iTryCount-- > 0 )
|
||||||
|
{
|
||||||
|
uint32_t ulStatus;
|
||||||
|
|
||||||
|
spi_clear_ovres();
|
||||||
|
/* Move register address to cmd bits 9-2, make 32-bit address. */
|
||||||
|
cmd = (reg << 2) & REG_ADDR_MASK;
|
||||||
|
|
||||||
|
/* Last 2 bits still under "don't care bits" handled with byte enable. */
|
||||||
|
/* Select byte enable for command. */
|
||||||
|
if (reg & 2) {
|
||||||
|
/* Odd word address writes bytes 2 and 3 */
|
||||||
|
cmd |= (0xc << 10);
|
||||||
|
} else {
|
||||||
|
/* Even word address write bytes 0 and 1 */
|
||||||
|
cmd |= (0x3 << 10);
|
||||||
|
}
|
||||||
|
|
||||||
|
/* Add command read code. */
|
||||||
|
cmd |= CMD_READ;
|
||||||
|
cmdBuf.uc[0] = cmd >> 8;
|
||||||
|
cmdBuf.uc[1] = cmd & 0xff;
|
||||||
|
cmdBuf.uc[2] = CONFIG_SPI_MASTER_DUMMY;
|
||||||
|
cmdBuf.uc[3] = CONFIG_SPI_MASTER_DUMMY;
|
||||||
|
|
||||||
|
/* Prepare PDC transfer. */
|
||||||
|
g_pdc_spi_tx_packet.ul_addr = (uint32_t) cmdBuf.uc;
|
||||||
|
g_pdc_spi_tx_packet.ul_size = 4;
|
||||||
|
g_pdc_spi_rx_packet.ul_addr = (uint32_t) tmpbuf;
|
||||||
|
g_pdc_spi_rx_packet.ul_size = 4;
|
||||||
|
pdc_disable_transfer(g_p_spi_pdc, PERIPH_PTCR_RXTDIS | PERIPH_PTCR_TXTDIS);
|
||||||
|
pdc_tx_init(g_p_spi_pdc, &g_pdc_spi_tx_packet, NULL);
|
||||||
|
pdc_rx_init(g_p_spi_pdc, &g_pdc_spi_rx_packet, NULL);
|
||||||
|
gpio_set_pin_low(KSZ8851SNL_CSN_GPIO);
|
||||||
|
|
||||||
|
spi_disable_interrupt( KSZ8851SNL_SPI, ~0ul );
|
||||||
|
pdc_enable_transfer(g_p_spi_pdc, PERIPH_PTCR_RXTEN | PERIPH_PTCR_TXTEN);
|
||||||
|
for( ;; )
|
||||||
|
{
|
||||||
|
ulStatus = spi_read_status( KSZ8851SNL_SPI );
|
||||||
|
if( ( ulStatus & ( SPI_SR_OVRES | SPI_SR_ENDRX ) ) != 0 )
|
||||||
|
{
|
||||||
|
break;
|
||||||
|
}
|
||||||
|
}
|
||||||
|
gpio_set_pin_high( KSZ8851SNL_CSN_GPIO );
|
||||||
|
if( ( ulStatus & SPI_SR_OVRES ) == 0 )
|
||||||
|
{
|
||||||
|
break;
|
||||||
|
}
|
||||||
|
pdc_disable_transfer(g_p_spi_pdc, PERIPH_PTCR_RXTDIS | PERIPH_PTCR_TXTDIS);
|
||||||
|
lUDPLoggingPrintf( "ksz8851_reg_read: SPI_SR_OVRES\n" );
|
||||||
|
}
|
||||||
|
|
||||||
|
res = (tmpbuf[3] << 8) | tmpbuf[2];
|
||||||
|
return res;
|
||||||
|
}
|
||||||
|
|
||||||
|
/**
|
||||||
|
* \brief Write a register value.
|
||||||
|
*
|
||||||
|
* \param reg the register address to modify.
|
||||||
|
* \param wrdata the new register value.
|
||||||
|
*/
|
||||||
|
void ksz8851_reg_write(uint16_t reg, uint16_t wrdata)
|
||||||
|
{
|
||||||
|
pdc_packet_t g_pdc_spi_tx_packet;
|
||||||
|
pdc_packet_t g_pdc_spi_rx_packet;
|
||||||
|
uint16_t cmd = 0;
|
||||||
|
int iTryCount = 3;
|
||||||
|
|
||||||
|
while( iTryCount-- > 0 )
|
||||||
|
{
|
||||||
|
uint32_t ulStatus;
|
||||||
|
|
||||||
|
|
||||||
|
spi_clear_ovres();
|
||||||
|
/* Move register address to cmd bits 9-2, make 32-bit address. */
|
||||||
|
cmd = (reg << 2) & REG_ADDR_MASK;
|
||||||
|
|
||||||
|
/* Last 2 bits still under "don't care bits" handled with byte enable. */
|
||||||
|
/* Select byte enable for command. */
|
||||||
|
if (reg & 2) {
|
||||||
|
/* Odd word address writes bytes 2 and 3 */
|
||||||
|
cmd |= (0xc << 10);
|
||||||
|
} else {
|
||||||
|
/* Even word address write bytes 0 and 1 */
|
||||||
|
cmd |= (0x3 << 10);
|
||||||
|
}
|
||||||
|
|
||||||
|
/* Add command write code. */
|
||||||
|
cmd |= CMD_WRITE;
|
||||||
|
cmdBuf.uc[0] = cmd >> 8;
|
||||||
|
cmdBuf.uc[1] = cmd & 0xff;
|
||||||
|
cmdBuf.uc[2] = wrdata & 0xff;
|
||||||
|
cmdBuf.uc[3] = wrdata >> 8;
|
||||||
|
|
||||||
|
/* Prepare PDC transfer. */
|
||||||
|
g_pdc_spi_tx_packet.ul_addr = (uint32_t) cmdBuf.uc;
|
||||||
|
g_pdc_spi_tx_packet.ul_size = 4;
|
||||||
|
g_pdc_spi_rx_packet.ul_addr = (uint32_t) tmpbuf;
|
||||||
|
g_pdc_spi_rx_packet.ul_size = 4;
|
||||||
|
pdc_disable_transfer(g_p_spi_pdc, PERIPH_PTCR_RXTDIS | PERIPH_PTCR_TXTDIS);
|
||||||
|
pdc_tx_init(g_p_spi_pdc, &g_pdc_spi_tx_packet, NULL);
|
||||||
|
pdc_rx_init(g_p_spi_pdc, &g_pdc_spi_rx_packet, NULL);
|
||||||
|
gpio_set_pin_low(KSZ8851SNL_CSN_GPIO);
|
||||||
|
|
||||||
|
spi_disable_interrupt( KSZ8851SNL_SPI, ~0ul );
|
||||||
|
|
||||||
|
pdc_enable_transfer(g_p_spi_pdc, PERIPH_PTCR_RXTEN | PERIPH_PTCR_TXTEN);
|
||||||
|
for( ;; )
|
||||||
|
{
|
||||||
|
ulStatus = spi_read_status( KSZ8851SNL_SPI );
|
||||||
|
if( ( ulStatus & ( SPI_SR_OVRES | SPI_SR_ENDRX ) ) != 0 )
|
||||||
|
{
|
||||||
|
break;
|
||||||
|
}
|
||||||
|
}
|
||||||
|
gpio_set_pin_high( KSZ8851SNL_CSN_GPIO );
|
||||||
|
if( ( ulStatus & SPI_SR_OVRES ) == 0 )
|
||||||
|
{
|
||||||
|
break;
|
||||||
|
}
|
||||||
|
pdc_disable_transfer(g_p_spi_pdc, PERIPH_PTCR_RXTDIS | PERIPH_PTCR_TXTDIS);
|
||||||
|
lUDPLoggingPrintf( "ksz8851_reg_write: SPI_SR_OVRES\n" );
|
||||||
|
}
|
||||||
|
}
|
||||||
|
|
||||||
|
static void spi_clear_ovres( void )
|
||||||
|
{
|
||||||
|
volatile uint32_t rc;
|
||||||
|
rc = KSZ8851SNL_SPI->SPI_RDR;
|
||||||
|
|
||||||
|
spi_read_status( KSZ8851SNL_SPI );
|
||||||
|
}
|
||||||
|
|
||||||
|
/**
|
||||||
|
* \brief Read internal fifo buffer.
|
||||||
|
*
|
||||||
|
* \param buf the buffer to store the data from the fifo buffer.
|
||||||
|
* \param len the amount of data to read.
|
||||||
|
*/
|
||||||
|
void ksz8851_fifo_read(uint8_t *buf, uint32_t len)
|
||||||
|
{
|
||||||
|
pdc_packet_t g_pdc_spi_tx_packet;
|
||||||
|
pdc_packet_t g_pdc_spi_rx_packet;
|
||||||
|
pdc_packet_t g_pdc_spi_tx_npacket;
|
||||||
|
pdc_packet_t g_pdc_spi_rx_npacket;
|
||||||
|
|
||||||
|
memset( cmdBuf.uc, '\0', sizeof cmdBuf );
|
||||||
|
cmdBuf.uc[0] = FIFO_READ;
|
||||||
|
spi_clear_ovres();
|
||||||
|
|
||||||
|
/* Prepare PDC transfer. */
|
||||||
|
g_pdc_spi_tx_packet.ul_addr = (uint32_t) cmdBuf.uc;
|
||||||
|
g_pdc_spi_tx_packet.ul_size = 9;
|
||||||
|
g_pdc_spi_rx_packet.ul_addr = (uint32_t) respBuf.uc;
|
||||||
|
g_pdc_spi_rx_packet.ul_size = 9;
|
||||||
|
|
||||||
|
g_pdc_spi_tx_npacket.ul_addr = (uint32_t) buf;
|
||||||
|
g_pdc_spi_tx_npacket.ul_size = len;
|
||||||
|
g_pdc_spi_rx_npacket.ul_addr = (uint32_t) buf;
|
||||||
|
g_pdc_spi_rx_npacket.ul_size = len;
|
||||||
|
pdc_disable_transfer(g_p_spi_pdc, PERIPH_PTCR_RXTDIS | PERIPH_PTCR_TXTDIS);
|
||||||
|
pdc_tx_init(g_p_spi_pdc, &g_pdc_spi_tx_packet, &g_pdc_spi_tx_npacket);
|
||||||
|
pdc_rx_init(g_p_spi_pdc, &g_pdc_spi_rx_packet, &g_pdc_spi_rx_npacket);
|
||||||
|
|
||||||
|
spi_enable_interrupt(KSZ8851SNL_SPI, SPI_IER_RXBUFF | SPI_IER_OVRES);
|
||||||
|
|
||||||
|
pdc_enable_transfer(g_p_spi_pdc, PERIPH_PTCR_RXTEN | PERIPH_PTCR_TXTEN);
|
||||||
|
}
|
||||||
|
|
||||||
|
/**
|
||||||
|
* \brief Write internal fifo buffer.
|
||||||
|
*
|
||||||
|
* \param buf the buffer to send to the fifo buffer.
|
||||||
|
* \param ulActualLength the total amount of data to write.
|
||||||
|
* \param ulFIFOLength the size of the first pbuf to write from the pbuf chain.
|
||||||
|
*/
|
||||||
|
void ksz8851_fifo_write(uint8_t *buf, uint32_t ulActualLength, uint32_t ulFIFOLength)
|
||||||
|
{
|
||||||
|
static uint8_t frameID = 0;
|
||||||
|
|
||||||
|
pdc_packet_t g_pdc_spi_tx_packet;
|
||||||
|
pdc_packet_t g_pdc_spi_rx_packet;
|
||||||
|
pdc_packet_t g_pdc_spi_tx_npacket;
|
||||||
|
pdc_packet_t g_pdc_spi_rx_npacket;
|
||||||
|
|
||||||
|
/* Prepare control word and byte count. */
|
||||||
|
cmdBuf.uc[0] = FIFO_WRITE;
|
||||||
|
cmdBuf.uc[1] = frameID++ & 0x3f;
|
||||||
|
cmdBuf.uc[2] = 0;
|
||||||
|
cmdBuf.uc[3] = ulActualLength & 0xff;
|
||||||
|
cmdBuf.uc[4] = ulActualLength >> 8;
|
||||||
|
|
||||||
|
spi_clear_ovres();
|
||||||
|
|
||||||
|
/* Prepare PDC transfer. */
|
||||||
|
g_pdc_spi_tx_packet.ul_addr = (uint32_t) cmdBuf.uc;
|
||||||
|
g_pdc_spi_tx_packet.ul_size = 5;
|
||||||
|
|
||||||
|
g_pdc_spi_rx_packet.ul_addr = (uint32_t) respBuf.uc;
|
||||||
|
g_pdc_spi_rx_packet.ul_size = 5;
|
||||||
|
|
||||||
|
g_pdc_spi_tx_npacket.ul_addr = (uint32_t) buf;
|
||||||
|
g_pdc_spi_tx_npacket.ul_size = ulFIFOLength;
|
||||||
|
|
||||||
|
g_pdc_spi_rx_npacket.ul_addr = (uint32_t) tmpbuf;
|
||||||
|
g_pdc_spi_rx_npacket.ul_size = ulFIFOLength;
|
||||||
|
|
||||||
|
pdc_disable_transfer(g_p_spi_pdc, PERIPH_PTCR_RXTDIS | PERIPH_PTCR_TXTDIS);
|
||||||
|
pdc_tx_init(g_p_spi_pdc, &g_pdc_spi_tx_packet, &g_pdc_spi_tx_npacket);
|
||||||
|
#if( TX_USES_RECV == 1 )
|
||||||
|
pdc_rx_init(g_p_spi_pdc, &g_pdc_spi_rx_packet, &g_pdc_spi_rx_npacket);
|
||||||
|
spi_enable_interrupt(KSZ8851SNL_SPI, SPI_IER_ENDRX | SPI_IER_OVRES);
|
||||||
|
pdc_enable_transfer(g_p_spi_pdc, PERIPH_PTCR_RXTEN | PERIPH_PTCR_TXTEN);
|
||||||
|
#else
|
||||||
|
spi_enable_interrupt(KSZ8851SNL_SPI, SPI_SR_TXBUFE | SPI_IER_OVRES);
|
||||||
|
pdc_enable_transfer(g_p_spi_pdc, PERIPH_PTCR_TXTEN);
|
||||||
|
#endif
|
||||||
|
}
|
||||||
|
|
||||||
|
/**
|
||||||
|
* \brief Write dummy data to the internal fifo buffer.
|
||||||
|
*
|
||||||
|
* \param len the amount of dummy data to write.
|
||||||
|
*/
|
||||||
|
void ksz8851_fifo_dummy(uint32_t len)
|
||||||
|
{
|
||||||
|
pdc_packet_t g_pdc_spi_tx_packet;
|
||||||
|
pdc_packet_t g_pdc_spi_rx_packet;
|
||||||
|
|
||||||
|
/* Prepare PDC transfer. */
|
||||||
|
g_pdc_spi_tx_packet.ul_addr = (uint32_t) tmpbuf;
|
||||||
|
g_pdc_spi_tx_packet.ul_size = len;
|
||||||
|
g_pdc_spi_rx_packet.ul_addr = (uint32_t) tmpbuf;
|
||||||
|
g_pdc_spi_rx_packet.ul_size = len;
|
||||||
|
pdc_disable_transfer(g_p_spi_pdc, PERIPH_PTCR_RXTDIS | PERIPH_PTCR_TXTDIS);
|
||||||
|
pdc_tx_init(g_p_spi_pdc, &g_pdc_spi_tx_packet, NULL);
|
||||||
|
pdc_rx_init(g_p_spi_pdc, &g_pdc_spi_rx_packet, NULL);
|
||||||
|
pdc_enable_transfer(g_p_spi_pdc, PERIPH_PTCR_RXTEN | PERIPH_PTCR_TXTEN);
|
||||||
|
|
||||||
|
while (!(spi_read_status(KSZ8851SNL_SPI) & SPI_SR_ENDRX))
|
||||||
|
;
|
||||||
|
}
|
||||||
|
|
||||||
|
void ksz8851snl_set_registers(void)
|
||||||
|
{
|
||||||
|
/* Init step2-4: write QMU MAC address (low, middle then high). */
|
||||||
|
ksz8851_reg_write(REG_MAC_ADDR_0, (ETHERNET_CONF_ETHADDR4 << 8) | ETHERNET_CONF_ETHADDR5);
|
||||||
|
ksz8851_reg_write(REG_MAC_ADDR_2, (ETHERNET_CONF_ETHADDR2 << 8) | ETHERNET_CONF_ETHADDR3);
|
||||||
|
ksz8851_reg_write(REG_MAC_ADDR_4, (ETHERNET_CONF_ETHADDR0 << 8) | ETHERNET_CONF_ETHADDR1);
|
||||||
|
|
||||||
|
/* Init step5: enable QMU Transmit Frame Data Pointer Auto Increment. */
|
||||||
|
ksz8851_reg_write(REG_TX_ADDR_PTR, ADDR_PTR_AUTO_INC);
|
||||||
|
|
||||||
|
/* Init step6: configure QMU transmit control register. */
|
||||||
|
ksz8851_reg_write(REG_TX_CTRL,
|
||||||
|
TX_CTRL_ICMP_CHECKSUM |
|
||||||
|
TX_CTRL_UDP_CHECKSUM |
|
||||||
|
TX_CTRL_TCP_CHECKSUM |
|
||||||
|
TX_CTRL_IP_CHECKSUM |
|
||||||
|
TX_CTRL_FLOW_ENABLE |
|
||||||
|
TX_CTRL_PAD_ENABLE |
|
||||||
|
TX_CTRL_CRC_ENABLE
|
||||||
|
);
|
||||||
|
|
||||||
|
/* Init step7: enable QMU Receive Frame Data Pointer Auto Increment. */
|
||||||
|
ksz8851_reg_write(REG_RX_ADDR_PTR, ADDR_PTR_AUTO_INC);
|
||||||
|
|
||||||
|
/* Init step8: configure QMU Receive Frame Threshold for one frame. */
|
||||||
|
ksz8851_reg_write(REG_RX_FRAME_CNT_THRES, 1);
|
||||||
|
|
||||||
|
/* Init step9: configure QMU receive control register1. */
|
||||||
|
ksz8851_reg_write(REG_RX_CTRL1,
|
||||||
|
RX_CTRL_UDP_CHECKSUM |
|
||||||
|
RX_CTRL_TCP_CHECKSUM |
|
||||||
|
RX_CTRL_IP_CHECKSUM |
|
||||||
|
RX_CTRL_MAC_FILTER |
|
||||||
|
RX_CTRL_FLOW_ENABLE |
|
||||||
|
RX_CTRL_BROADCAST |
|
||||||
|
RX_CTRL_ALL_MULTICAST|
|
||||||
|
RX_CTRL_UNICAST);
|
||||||
|
// ksz8851_reg_write(REG_RX_CTRL1,
|
||||||
|
// RX_CTRL_UDP_CHECKSUM |
|
||||||
|
// RX_CTRL_TCP_CHECKSUM |
|
||||||
|
// RX_CTRL_IP_CHECKSUM |
|
||||||
|
// RX_CTRL_FLOW_ENABLE |
|
||||||
|
// RX_CTRL_PROMISCUOUS);
|
||||||
|
|
||||||
|
ksz8851_reg_write(REG_RX_CTRL2,
|
||||||
|
RX_CTRL_IPV6_UDP_NOCHECKSUM |
|
||||||
|
RX_CTRL_UDP_LITE_CHECKSUM |
|
||||||
|
RX_CTRL_ICMP_CHECKSUM |
|
||||||
|
RX_CTRL_BURST_LEN_FRAME);
|
||||||
|
|
||||||
|
|
||||||
|
//#define RXQ_TWOBYTE_OFFSET (0x0200) /* Enable adding 2-byte before frame header for IP aligned with DWORD */
|
||||||
|
#warning Remember to try the above option to get a 2-byte offset
|
||||||
|
|
||||||
|
/* Init step11: configure QMU receive queue: trigger INT and auto-dequeue frame. */
|
||||||
|
ksz8851_reg_write( REG_RXQ_CMD, RXQ_CMD_CNTL | RXQ_TWOBYTE_OFFSET );
|
||||||
|
|
||||||
|
/* Init step12: adjust SPI data output delay. */
|
||||||
|
ksz8851_reg_write(REG_BUS_CLOCK_CTRL, BUS_CLOCK_166 | BUS_CLOCK_DIVIDEDBY_1);
|
||||||
|
|
||||||
|
/* Init step13: restart auto-negotiation. */
|
||||||
|
ksz8851_reg_setbits(REG_PORT_CTRL, PORT_AUTO_NEG_RESTART);
|
||||||
|
|
||||||
|
/* Init step13.1: force link in half duplex if auto-negotiation failed. */
|
||||||
|
if ((ksz8851_reg_read(REG_PORT_CTRL) & PORT_AUTO_NEG_RESTART) != PORT_AUTO_NEG_RESTART)
|
||||||
|
{
|
||||||
|
ksz8851_reg_clrbits(REG_PORT_CTRL, PORT_FORCE_FULL_DUPLEX);
|
||||||
|
}
|
||||||
|
|
||||||
|
/* Init step14: clear interrupt status. */
|
||||||
|
ksz8851_reg_write(REG_INT_STATUS, 0xFFFF);
|
||||||
|
|
||||||
|
/* Init step15: set interrupt mask. */
|
||||||
|
ksz8851_reg_write(REG_INT_MASK, INT_RX);
|
||||||
|
|
||||||
|
/* Init step16: enable QMU Transmit. */
|
||||||
|
ksz8851_reg_setbits(REG_TX_CTRL, TX_CTRL_ENABLE);
|
||||||
|
|
||||||
|
/* Init step17: enable QMU Receive. */
|
||||||
|
ksz8851_reg_setbits(REG_RX_CTRL1, RX_CTRL_ENABLE);
|
||||||
|
}
|
||||||
|
/**
|
||||||
|
* \brief KSZ8851SNL initialization function.
|
||||||
|
*
|
||||||
|
* \return 0 on success, 1 on communication error.
|
||||||
|
*/
|
||||||
|
uint32_t ksz8851snl_init(void)
|
||||||
|
{
|
||||||
|
uint32_t count = 10;
|
||||||
|
uint16_t dev_id = 0;
|
||||||
|
uint8_t id_ok = 0;
|
||||||
|
|
||||||
|
/* Configure the SPI peripheral. */
|
||||||
|
spi_enable_clock(KSZ8851SNL_SPI);
|
||||||
|
spi_disable(KSZ8851SNL_SPI);
|
||||||
|
spi_reset(KSZ8851SNL_SPI);
|
||||||
|
spi_set_master_mode(KSZ8851SNL_SPI);
|
||||||
|
spi_disable_mode_fault_detect(KSZ8851SNL_SPI);
|
||||||
|
spi_set_peripheral_chip_select_value(KSZ8851SNL_SPI, ~(uint32_t)(1UL << KSZ8851SNL_CS_PIN));
|
||||||
|
spi_set_fixed_peripheral_select(KSZ8851SNL_SPI);
|
||||||
|
//spi_disable_peripheral_select_decode(KSZ8851SNL_SPI);
|
||||||
|
|
||||||
|
spi_set_clock_polarity(KSZ8851SNL_SPI, KSZ8851SNL_CS_PIN, SPI_CLK_POLARITY);
|
||||||
|
spi_set_clock_phase(KSZ8851SNL_SPI, KSZ8851SNL_CS_PIN, SPI_CLK_PHASE);
|
||||||
|
spi_set_bits_per_transfer(KSZ8851SNL_SPI, KSZ8851SNL_CS_PIN,
|
||||||
|
SPI_CSR_BITS_8_BIT);
|
||||||
|
spi_set_baudrate_div(KSZ8851SNL_SPI, KSZ8851SNL_CS_PIN, (sysclk_get_cpu_hz() / KSZ8851SNL_CLOCK_SPEED));
|
||||||
|
// spi_set_transfer_delay(KSZ8851SNL_SPI, KSZ8851SNL_CS_PIN, CONFIG_SPI_MASTER_DELAY_BS,
|
||||||
|
// CONFIG_SPI_MASTER_DELAY_BCT);
|
||||||
|
|
||||||
|
|
||||||
|
spi_set_transfer_delay(KSZ8851SNL_SPI, KSZ8851SNL_CS_PIN, 0, 0);
|
||||||
|
|
||||||
|
spi_enable(KSZ8851SNL_SPI);
|
||||||
|
|
||||||
|
/* Get pointer to UART PDC register base. */
|
||||||
|
g_p_spi_pdc = spi_get_pdc_base(KSZ8851SNL_SPI);
|
||||||
|
pdc_enable_transfer(g_p_spi_pdc, PERIPH_PTCR_RXTEN | PERIPH_PTCR_TXTEN);
|
||||||
|
|
||||||
|
/* Control RSTN and CSN pin from the driver. */
|
||||||
|
gpio_configure_pin(KSZ8851SNL_CSN_GPIO, KSZ8851SNL_CSN_FLAGS);
|
||||||
|
gpio_set_pin_high(KSZ8851SNL_CSN_GPIO);
|
||||||
|
gpio_configure_pin(KSZ8851SNL_RSTN_GPIO, KSZ8851SNL_RSTN_FLAGS);
|
||||||
|
|
||||||
|
/* Reset the Micrel in a proper state. */
|
||||||
|
while( count-- )
|
||||||
|
{
|
||||||
|
/* Perform hardware reset with respect to the reset timing from the datasheet. */
|
||||||
|
gpio_set_pin_low(KSZ8851SNL_RSTN_GPIO);
|
||||||
|
vTaskDelay(2);
|
||||||
|
gpio_set_pin_high(KSZ8851SNL_RSTN_GPIO);
|
||||||
|
vTaskDelay(2);
|
||||||
|
|
||||||
|
/* Init step1: read chip ID. */
|
||||||
|
dev_id = ksz8851_reg_read(REG_CHIP_ID);
|
||||||
|
if( ( dev_id & 0xFFF0 ) == CHIP_ID_8851_16 )
|
||||||
|
{
|
||||||
|
id_ok = 1;
|
||||||
|
break;
|
||||||
|
}
|
||||||
|
}
|
||||||
|
if( id_ok != 0 )
|
||||||
|
{
|
||||||
|
ksz8851snl_set_registers();
|
||||||
|
}
|
||||||
|
|
||||||
|
return id_ok ? 1 : -1;
|
||||||
|
}
|
||||||
|
|
||||||
|
uint32_t ksz8851snl_reinit(void)
|
||||||
|
{
|
||||||
|
uint32_t count = 10;
|
||||||
|
uint16_t dev_id = 0;
|
||||||
|
uint8_t id_ok = 0;
|
||||||
|
/* Reset the Micrel in a proper state. */
|
||||||
|
while( count-- )
|
||||||
|
{
|
||||||
|
/* Perform hardware reset with respect to the reset timing from the datasheet. */
|
||||||
|
gpio_set_pin_low(KSZ8851SNL_RSTN_GPIO);
|
||||||
|
vTaskDelay(2);
|
||||||
|
gpio_set_pin_high(KSZ8851SNL_RSTN_GPIO);
|
||||||
|
vTaskDelay(2);
|
||||||
|
|
||||||
|
/* Init step1: read chip ID. */
|
||||||
|
dev_id = ksz8851_reg_read(REG_CHIP_ID);
|
||||||
|
if( ( dev_id & 0xFFF0 ) == CHIP_ID_8851_16 )
|
||||||
|
{
|
||||||
|
id_ok = 1;
|
||||||
|
break;
|
||||||
|
}
|
||||||
|
}
|
||||||
|
if( id_ok != 0 )
|
||||||
|
{
|
||||||
|
ksz8851snl_set_registers();
|
||||||
|
}
|
||||||
|
|
||||||
|
return id_ok ? 1 : -1;
|
||||||
|
}
|
||||||
|
|
||||||
|
uint32_t ksz8851snl_reset_rx( void )
|
||||||
|
{
|
||||||
|
uint16_t usValue;
|
||||||
|
|
||||||
|
usValue = ksz8851_reg_read(REG_RX_CTRL1);
|
||||||
|
|
||||||
|
usValue &= ~( ( uint16_t ) RX_CTRL_ENABLE | RX_CTRL_FLUSH_QUEUE );
|
||||||
|
|
||||||
|
ksz8851_reg_write( REG_RX_CTRL1, usValue ); vTaskDelay( 2 );
|
||||||
|
ksz8851_reg_write( REG_RX_CTRL1, usValue | RX_CTRL_FLUSH_QUEUE ); vTaskDelay( 1 );
|
||||||
|
ksz8851_reg_write( REG_RX_CTRL1, usValue ); vTaskDelay( 1 );
|
||||||
|
ksz8851_reg_write( REG_RX_CTRL1, usValue | RX_CTRL_ENABLE ); vTaskDelay( 1 );
|
||||||
|
|
||||||
|
return ( uint32_t )usValue;
|
||||||
|
}
|
||||||
|
|
||||||
|
uint32_t ksz8851snl_reset_tx( void )
|
||||||
|
{
|
||||||
|
uint16_t usValue;
|
||||||
|
|
||||||
|
usValue = ksz8851_reg_read( REG_TX_CTRL );
|
||||||
|
|
||||||
|
usValue &= ~( ( uint16_t ) TX_CTRL_ENABLE | TX_CTRL_FLUSH_QUEUE );
|
||||||
|
|
||||||
|
ksz8851_reg_write( REG_TX_CTRL, usValue ); vTaskDelay( 2 );
|
||||||
|
ksz8851_reg_write( REG_TX_CTRL, usValue | TX_CTRL_FLUSH_QUEUE ); vTaskDelay( 1 );
|
||||||
|
ksz8851_reg_write( REG_TX_CTRL, usValue ); vTaskDelay( 1 );
|
||||||
|
ksz8851_reg_write( REG_TX_CTRL, usValue | TX_CTRL_ENABLE ); vTaskDelay( 1 );
|
||||||
|
|
||||||
|
return ( uint32_t )usValue;
|
||||||
|
}
|
||||||
@ -0,0 +1,67 @@
|
|||||||
|
/**
|
||||||
|
*
|
||||||
|
* \file
|
||||||
|
*
|
||||||
|
* \brief KS8851SNL driver for SAM.
|
||||||
|
*
|
||||||
|
* Copyright (c) 2013-2015 Atmel Corporation. All rights reserved.
|
||||||
|
*
|
||||||
|
* \asf_license_start
|
||||||
|
*
|
||||||
|
* \page License
|
||||||
|
*
|
||||||
|
* Redistribution and use in source and binary forms, with or without
|
||||||
|
* modification, are permitted provided that the following conditions are met:
|
||||||
|
*
|
||||||
|
* 1. Redistributions of source code must retain the above copyright notice,
|
||||||
|
* this list of conditions and the following disclaimer.
|
||||||
|
*
|
||||||
|
* 2. Redistributions in binary form must reproduce the above copyright notice,
|
||||||
|
* this list of conditions and the following disclaimer in the documentation
|
||||||
|
* and/or other materials provided with the distribution.
|
||||||
|
*
|
||||||
|
* 3. The name of Atmel may not be used to endorse or promote products derived
|
||||||
|
* from this software without specific prior written permission.
|
||||||
|
*
|
||||||
|
* 4. This software may only be redistributed and used in connection with an
|
||||||
|
* Atmel microcontroller product.
|
||||||
|
*
|
||||||
|
* THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
|
||||||
|
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
|
||||||
|
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
|
||||||
|
* EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
|
||||||
|
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
||||||
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
||||||
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
||||||
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
||||||
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||||
|
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||||
|
* POSSIBILITY OF SUCH DAMAGE.
|
||||||
|
*
|
||||||
|
* \asf_license_stop
|
||||||
|
*
|
||||||
|
*/
|
||||||
|
/*
|
||||||
|
* Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a>
|
||||||
|
*/
|
||||||
|
|
||||||
|
#ifndef KSZ8851SNL_H_INCLUDED
|
||||||
|
#define KSZ8851SNL_H_INCLUDED
|
||||||
|
|
||||||
|
#include "gpio.h"
|
||||||
|
|
||||||
|
void configure_intn(void (*p_handler) (uint32_t, uint32_t));
|
||||||
|
void ksz8851_reg_setbits(uint16_t reg, uint16_t bits_to_set);
|
||||||
|
void ksz8851_reg_clrbits(uint16_t reg, uint16_t bits_to_clr);
|
||||||
|
void ksz8851_fifo_read(uint8_t *buf, uint32_t len);
|
||||||
|
void ksz8851_fifo_write(uint8_t *buf, uint32_t ulActualLength, uint32_t ulFIFOLength);
|
||||||
|
void ksz8851_fifo_dummy(uint32_t len);
|
||||||
|
void ksz8851_reg_write(uint16_t reg, uint16_t wrdata);
|
||||||
|
uint16_t ksz8851_reg_read(uint16_t reg);
|
||||||
|
uint32_t ksz8851snl_init(void);
|
||||||
|
uint32_t ksz8851snl_reinit(void);
|
||||||
|
|
||||||
|
uint32_t ksz8851snl_reset_rx( void );
|
||||||
|
uint32_t ksz8851snl_reset_tx( void );
|
||||||
|
|
||||||
|
#endif /* KSZ8851SNL_H_INCLUDED */
|
||||||
@ -0,0 +1,473 @@
|
|||||||
|
/**
|
||||||
|
*
|
||||||
|
* \file
|
||||||
|
*
|
||||||
|
* \brief KS8851SNL registers definitions.
|
||||||
|
*
|
||||||
|
* Copyright (c) 2013-2015 Atmel Corporation. All rights reserved.
|
||||||
|
*
|
||||||
|
* \asf_license_start
|
||||||
|
*
|
||||||
|
* \page License
|
||||||
|
*
|
||||||
|
* Redistribution and use in source and binary forms, with or without
|
||||||
|
* modification, are permitted provided that the following conditions are met:
|
||||||
|
*
|
||||||
|
* 1. Redistributions of source code must retain the above copyright notice,
|
||||||
|
* this list of conditions and the following disclaimer.
|
||||||
|
*
|
||||||
|
* 2. Redistributions in binary form must reproduce the above copyright notice,
|
||||||
|
* this list of conditions and the following disclaimer in the documentation
|
||||||
|
* and/or other materials provided with the distribution.
|
||||||
|
*
|
||||||
|
* 3. The name of Atmel may not be used to endorse or promote products derived
|
||||||
|
* from this software without specific prior written permission.
|
||||||
|
*
|
||||||
|
* 4. This software may only be redistributed and used in connection with an
|
||||||
|
* Atmel microcontroller product.
|
||||||
|
*
|
||||||
|
* THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
|
||||||
|
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
|
||||||
|
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
|
||||||
|
* EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
|
||||||
|
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
||||||
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
||||||
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
||||||
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
||||||
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||||
|
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||||
|
* POSSIBILITY OF SUCH DAMAGE.
|
||||||
|
*
|
||||||
|
* \asf_license_stop
|
||||||
|
*
|
||||||
|
*/
|
||||||
|
/*
|
||||||
|
* Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a>
|
||||||
|
*/
|
||||||
|
|
||||||
|
#ifndef KSZ8851SNL_REG_H_INCLUDED
|
||||||
|
#define KSZ8851SNL_REG_H_INCLUDED
|
||||||
|
|
||||||
|
#define REG_ADDR_MASK (0x3F0) /* Register address mask */
|
||||||
|
#define OPCODE_MASK (3 << 14)
|
||||||
|
#define CMD_READ (0 << 14)
|
||||||
|
#define CMD_WRITE (1 << 14)
|
||||||
|
#define FIFO_READ (0x80)
|
||||||
|
#define FIFO_WRITE (0xC0)
|
||||||
|
|
||||||
|
/*
|
||||||
|
* MAC Registers
|
||||||
|
* (Offset 0x00 - 0x25)
|
||||||
|
*/
|
||||||
|
#define REG_BUS_ERROR_STATUS (0x06) /* BESR */
|
||||||
|
#define BUS_ERROR_IBEC (0x8000)
|
||||||
|
#define BUS_ERROR_IBECV_MASK (0x7800) /* Default IPSec clock at 166Mhz */
|
||||||
|
|
||||||
|
#define REG_CHIP_CFG_STATUS (0x08) /* CCFG */
|
||||||
|
#define LITTLE_ENDIAN_BUS_MODE (0x0400) /* Bus in little endian mode */
|
||||||
|
#define EEPROM_PRESENCE (0x0200) /* External EEPROM is used */
|
||||||
|
#define SPI_BUS_MODE (0x0100) /* In SPI bus mode */
|
||||||
|
#define DATA_BUS_8BIT (0x0080) /* In 8-bit bus mode operation */
|
||||||
|
#define DATA_BUS_16BIT (0x0040) /* In 16-bit bus mode operation */
|
||||||
|
#define DATA_BUS_32BIT (0x0020) /* In 32-bit bus mode operation */
|
||||||
|
#define MULTIPLEX_MODE (0x0010) /* Data and address bus are shared */
|
||||||
|
#define CHIP_PACKAGE_128PIN (0x0008) /* 128-pin package */
|
||||||
|
#define CHIP_PACKAGE_80PIN (0x0004) /* 80-pin package */
|
||||||
|
#define CHIP_PACKAGE_48PIN (0x0002) /* 48-pin package */
|
||||||
|
#define CHIP_PACKAGE_32PIN (0x0001) /* 32-pin package for SPI host interface only */
|
||||||
|
|
||||||
|
#define REG_MAC_ADDR_0 (0x10) /* MARL */
|
||||||
|
#define REG_MAC_ADDR_1 (0x11) /* MARL */
|
||||||
|
#define REG_MAC_ADDR_2 (0x12) /* MARM */
|
||||||
|
#define REG_MAC_ADDR_3 (0x13) /* MARM */
|
||||||
|
#define REG_MAC_ADDR_4 (0x14) /* MARH */
|
||||||
|
#define REG_MAC_ADDR_5 (0x15) /* MARH */
|
||||||
|
|
||||||
|
#define REG_BUS_CLOCK_CTRL (0x20) /* OBCR */
|
||||||
|
#define BUS_CLOCK_166 (0x0004) /* 166 MHz on-chip bus clock (defaul is 125MHz) */
|
||||||
|
#define BUS_CLOCK_DIVIDEDBY_5 (0x0003) /* Bus clock devided by 5 */
|
||||||
|
#define BUS_CLOCK_DIVIDEDBY_3 (0x0002) /* Bus clock devided by 3 */
|
||||||
|
#define BUS_CLOCK_DIVIDEDBY_2 (0x0001) /* Bus clock devided by 2 */
|
||||||
|
#define BUS_CLOCK_DIVIDEDBY_1 (0x0000) /* Bus clock devided by 1 */
|
||||||
|
#define BUS_CLOCK_DIVIDED_MASK (0x0003) /* Bus clock devider mask */
|
||||||
|
|
||||||
|
#define BUS_SPEED_166_MHZ (0x0004) /* Set bus speed to 166 MHz */
|
||||||
|
#define BUS_SPEED_125_MHZ (0x0000) /* Set bus speed to 125 MHz */
|
||||||
|
#define BUS_SPEED_83_MHZ (0x0005) /* Set bus speed to 83 MHz (166/2)*/
|
||||||
|
#define BUS_SPEED_62_5_MHZ (0x0001) /* Set bus speed to 62.5 MHz (125/2) */
|
||||||
|
#define BUS_SPEED_53_3_MHZ (0x0006) /* Set bus speed to 53.3 MHz (166/3) */
|
||||||
|
#define BUS_SPEED_41_7_MHZ (0x0002) /* Set bus speed to 41.67 MHz (125/3) */
|
||||||
|
#define BUS_SPEED_33_2_MHZ (0x0007) /* Set bus speed to 33.2 MHz (166/5) */
|
||||||
|
#define BUS_SPEED_25_MHZ (0x0003) /* Set bus speed to 25 MHz (125/5) */
|
||||||
|
|
||||||
|
#define REG_EEPROM_CTRL (0x22) /* EEPCR */
|
||||||
|
#define EEPROM_ACCESS_ENABLE (0x0010) /* Enable software to access EEPROM through bit 3 to bit 0 */
|
||||||
|
#define EEPROM_DATA_IN (0x0008) /* Data receive from EEPROM (EEDI pin) */
|
||||||
|
#define EEPROM_DATA_OUT (0x0004) /* Data transmit to EEPROM (EEDO pin) */
|
||||||
|
#define EEPROM_SERIAL_CLOCK (0x0002) /* Serial clock (EESK pin) */
|
||||||
|
#define EEPROM_CHIP_SELECT (0x0001) /* EEPROM chip select (EECS pin) */
|
||||||
|
|
||||||
|
#define REG_MEM_BIST_INFO (0x24) /* MBIR */
|
||||||
|
#define TX_MEM_TEST_FINISHED (0x1000) /* TX memeory BIST test finish */
|
||||||
|
#define TX_MEM_TEST_FAILED (0x0800) /* TX memory BIST test fail */
|
||||||
|
#define TX_MEM_TEST_FAILED_COUNT (0x0700) /* TX memory BIST test fail count */
|
||||||
|
#define RX_MEM_TEST_FINISHED (0x0010) /* RX memory BIST test finish */
|
||||||
|
#define RX_MEM_TEST_FAILED (0x0008) /* RX memory BIST test fail */
|
||||||
|
#define RX_MEM_TEST_FAILED_COUNT (0x0003) /* RX memory BIST test fail count */
|
||||||
|
|
||||||
|
#define REG_RESET_CTRL (0x26) /* GRR */
|
||||||
|
#define QMU_SOFTWARE_RESET (0x0002) /* QMU soft reset (clear TxQ, RxQ) */
|
||||||
|
#define GLOBAL_SOFTWARE_RESET (0x0001) /* Global soft reset (PHY, MAC, QMU) */
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Wake On Lan Control Registers
|
||||||
|
* (Offset 0x2A - 0x6B)
|
||||||
|
*/
|
||||||
|
#define REG_WOL_CTRL (0x2A) /* WFCR */
|
||||||
|
#define WOL_MAGIC_ENABLE (0x0080) /* Enable the magic packet pattern detection */
|
||||||
|
#define WOL_FRAME3_ENABLE (0x0008) /* Enable the wake up frame 3 pattern detection */
|
||||||
|
#define WOL_FRAME2_ENABLE (0x0004) /* Enable the wake up frame 2 pattern detection */
|
||||||
|
#define WOL_FRAME1_ENABLE (0x0002) /* Enable the wake up frame 1 pattern detection */
|
||||||
|
#define WOL_FRAME0_ENABLE (0x0001) /* Enable the wake up frame 0 pattern detection */
|
||||||
|
|
||||||
|
#define REG_WOL_FRAME0_CRC0 (0x30) /* WF0CRC0 */
|
||||||
|
#define REG_WOL_FRAME0_CRC1 (0x32) /* WF0CRC1 */
|
||||||
|
#define REG_WOL_FRAME0_BYTE_MASK0 (0x34) /* WF0BM0 */
|
||||||
|
#define REG_WOL_FRAME0_BYTE_MASK1 (0x36) /* WF0BM1 */
|
||||||
|
#define REG_WOL_FRAME0_BYTE_MASK2 (0x38) /* WF0BM2 */
|
||||||
|
#define REG_WOL_FRAME0_BYTE_MASK3 (0x3A) /* WF0BM3 */
|
||||||
|
|
||||||
|
#define REG_WOL_FRAME1_CRC0 (0x40) /* WF1CRC0 */
|
||||||
|
#define REG_WOL_FRAME1_CRC1 (0x42) /* WF1CRC1 */
|
||||||
|
#define REG_WOL_FRAME1_BYTE_MASK0 (0x44) /* WF1BM0 */
|
||||||
|
#define REG_WOL_FRAME1_BYTE_MASK1 (0x46) /* WF1BM1 */
|
||||||
|
#define REG_WOL_FRAME1_BYTE_MASK2 (0x48) /* WF1BM2 */
|
||||||
|
#define REG_WOL_FRAME1_BYTE_MASK3 (0x4A) /* WF1BM3 */
|
||||||
|
|
||||||
|
#define REG_WOL_FRAME2_CRC0 (0x50) /* WF2CRC0 */
|
||||||
|
#define REG_WOL_FRAME2_CRC1 (0x52) /* WF2CRC1 */
|
||||||
|
#define REG_WOL_FRAME2_BYTE_MASK0 (0x54) /* WF2BM0 */
|
||||||
|
#define REG_WOL_FRAME2_BYTE_MASK1 (0x56) /* WF2BM1 */
|
||||||
|
#define REG_WOL_FRAME2_BYTE_MASK2 (0x58) /* WF2BM2 */
|
||||||
|
#define REG_WOL_FRAME2_BYTE_MASK3 (0x5A) /* WF2BM3 */
|
||||||
|
|
||||||
|
#define REG_WOL_FRAME3_CRC0 (0x60) /* WF3CRC0 */
|
||||||
|
#define REG_WOL_FRAME3_CRC1 (0x62) /* WF3CRC1 */
|
||||||
|
#define REG_WOL_FRAME3_BYTE_MASK0 (0x64) /* WF3BM0 */
|
||||||
|
#define REG_WOL_FRAME3_BYTE_MASK1 (0x66) /* WF3BM1 */
|
||||||
|
#define REG_WOL_FRAME3_BYTE_MASK2 (0x68) /* WF3BM2 */
|
||||||
|
#define REG_WOL_FRAME3_BYTE_MASK3 (0x6A) /* WF3BM3 */
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Transmit/Receive Control Registers
|
||||||
|
* (Offset 0x70 - 0x9F)
|
||||||
|
*/
|
||||||
|
|
||||||
|
/* Transmit Frame Header */
|
||||||
|
#define REG_QDR_DUMMY (0x00) /* Dummy address to access QMU RxQ, TxQ */
|
||||||
|
#define TX_CTRL_INTERRUPT_ON (0x8000) /* Transmit Interrupt on Completion */
|
||||||
|
|
||||||
|
#define REG_TX_CTRL (0x70) /* TXCR */
|
||||||
|
#define TX_CTRL_ICMP_CHECKSUM (0x0100) /* Enable ICMP frame checksum generation */
|
||||||
|
#define TX_CTRL_UDP_CHECKSUM (0x0080) /* Enable UDP frame checksum generation */
|
||||||
|
#define TX_CTRL_TCP_CHECKSUM (0x0040) /* Enable TCP frame checksum generation */
|
||||||
|
#define TX_CTRL_IP_CHECKSUM (0x0020) /* Enable IP frame checksum generation */
|
||||||
|
#define TX_CTRL_FLUSH_QUEUE (0x0010) /* Clear transmit queue, reset tx frame pointer */
|
||||||
|
#define TX_CTRL_FLOW_ENABLE (0x0008) /* Enable transmit flow control */
|
||||||
|
#define TX_CTRL_PAD_ENABLE (0x0004) /* Eanble adding a padding to a packet shorter than 64 bytes */
|
||||||
|
#define TX_CTRL_CRC_ENABLE (0x0002) /* Enable adding a CRC to the end of transmit frame */
|
||||||
|
#define TX_CTRL_ENABLE (0x0001) /* Enable tranmsit */
|
||||||
|
|
||||||
|
#define REG_TX_STATUS (0x72) /* TXSR */
|
||||||
|
#define TX_STAT_LATE_COL (0x2000) /* Tranmsit late collision occurs */
|
||||||
|
#define TX_STAT_MAX_COL (0x1000) /* Tranmsit maximum collision is reached */
|
||||||
|
#define TX_FRAME_ID_MASK (0x003F) /* Transmit frame ID mask */
|
||||||
|
#define TX_STAT_ERRORS ( TX_STAT_MAX_COL | TX_STAT_LATE_COL )
|
||||||
|
|
||||||
|
#define REG_RX_CTRL1 (0x74) /* RXCR1 */
|
||||||
|
#define RX_CTRL_FLUSH_QUEUE (0x8000) /* Clear receive queue, reset rx frame pointer */
|
||||||
|
#define RX_CTRL_UDP_CHECKSUM (0x4000) /* Enable UDP frame checksum verification */
|
||||||
|
#define RX_CTRL_TCP_CHECKSUM (0x2000) /* Enable TCP frame checksum verification */
|
||||||
|
#define RX_CTRL_IP_CHECKSUM (0x1000) /* Enable IP frame checksum verification */
|
||||||
|
#define RX_CTRL_MAC_FILTER (0x0800) /* Receive with address that pass MAC address filtering */
|
||||||
|
#define RX_CTRL_FLOW_ENABLE (0x0400) /* Enable receive flow control */
|
||||||
|
#define RX_CTRL_BAD_PACKET (0x0200) /* Eanble receive CRC error frames */
|
||||||
|
#define RX_CTRL_MULTICAST (0x0100) /* Receive multicast frames that pass the CRC hash filtering */
|
||||||
|
#define RX_CTRL_BROADCAST (0x0080) /* Receive all the broadcast frames */
|
||||||
|
#define RX_CTRL_ALL_MULTICAST (0x0040) /* Receive all the multicast frames (including broadcast frames) */
|
||||||
|
#define RX_CTRL_UNICAST (0x0020) /* Receive unicast frames that match the device MAC address */
|
||||||
|
#define RX_CTRL_PROMISCUOUS (0x0010) /* Receive all incoming frames, regardless of frame's DA */
|
||||||
|
#define RX_CTRL_STRIP_CRC (0x0008) /* Enable strip CRC on the received frames */
|
||||||
|
#define RX_CTRL_INVERSE_FILTER (0x0002) /* Receive with address check in inverse filtering mode */
|
||||||
|
#define RX_CTRL_ENABLE (0x0001) /* Enable receive */
|
||||||
|
|
||||||
|
/* Address filtering scheme mask */
|
||||||
|
#define RX_CTRL_FILTER_MASK ( RX_CTRL_INVERSE_FILTER | RX_CTRL_PROMISCUOUS | RX_CTRL_MULTICAST | RX_CTRL_MAC_FILTER )
|
||||||
|
|
||||||
|
#define REG_RX_CTRL2 (0x76) /* RXCR2 */
|
||||||
|
#define RX_CTRL_IPV6_UDP_NOCHECKSUM (0x0010) /* No checksum generation and verification if IPv6 UDP is fragment */
|
||||||
|
#define RX_CTRL_IPV6_UDP_CHECKSUM (0x0008) /* Receive pass IPv6 UDP frame with UDP checksum is zero */
|
||||||
|
#define RX_CTRL_UDP_LITE_CHECKSUM (0x0004) /* Enable UDP Lite frame checksum generation and verification */
|
||||||
|
#define RX_CTRL_ICMP_CHECKSUM (0x0002) /* Enable ICMP frame checksum verification */
|
||||||
|
#define RX_CTRL_BLOCK_MAC (0x0001) /* Receive drop frame if the SA is same as device MAC address */
|
||||||
|
#define RX_CTRL_BURST_LEN_MASK (0x00e0) /* SRDBL SPI Receive Data Burst Length */
|
||||||
|
#define RX_CTRL_BURST_LEN_4 (0x0000)
|
||||||
|
#define RX_CTRL_BURST_LEN_8 (0x0020)
|
||||||
|
#define RX_CTRL_BURST_LEN_16 (0x0040)
|
||||||
|
#define RX_CTRL_BURST_LEN_32 (0x0060)
|
||||||
|
#define RX_CTRL_BURST_LEN_FRAME (0x0080)
|
||||||
|
|
||||||
|
#define REG_TX_MEM_INFO (0x78) /* TXMIR */
|
||||||
|
#define TX_MEM_AVAILABLE_MASK (0x1FFF) /* The amount of memory available in TXQ */
|
||||||
|
|
||||||
|
#define REG_RX_FHR_STATUS (0x7C) /* RXFHSR */
|
||||||
|
#define RX_VALID (0x8000) /* Frame in the receive packet memory is valid */
|
||||||
|
#define RX_ICMP_ERROR (0x2000) /* ICMP checksum field doesn't match */
|
||||||
|
#define RX_IP_ERROR (0x1000) /* IP checksum field doesn't match */
|
||||||
|
#define RX_TCP_ERROR (0x0800) /* TCP checksum field doesn't match */
|
||||||
|
#define RX_UDP_ERROR (0x0400) /* UDP checksum field doesn't match */
|
||||||
|
#define RX_BROADCAST (0x0080) /* Received frame is a broadcast frame */
|
||||||
|
#define RX_MULTICAST (0x0040) /* Received frame is a multicast frame */
|
||||||
|
#define RX_UNICAST (0x0020) /* Received frame is a unicast frame */
|
||||||
|
#define RX_PHY_ERROR (0x0010) /* Received frame has runt error */
|
||||||
|
#define RX_FRAME_ETHER (0x0008) /* Received frame is an Ethernet-type frame */
|
||||||
|
#define RX_TOO_LONG (0x0004) /* Received frame length exceeds max size 0f 2048 bytes */
|
||||||
|
#define RX_RUNT_ERROR (0x0002) /* Received frame was demaged by a collision */
|
||||||
|
#define RX_BAD_CRC (0x0001) /* Received frame has a CRC error */
|
||||||
|
#define RX_ERRORS ( RX_BAD_CRC | RX_TOO_LONG | RX_RUNT_ERROR | RX_PHY_ERROR | \
|
||||||
|
RX_ICMP_ERROR | RX_IP_ERROR | RX_TCP_ERROR | RX_UDP_ERROR )
|
||||||
|
|
||||||
|
#define REG_RX_FHR_BYTE_CNT (0x7E) /* RXFHBCR */
|
||||||
|
#define RX_BYTE_CNT_MASK (0x0FFF) /* Received frame byte size mask */
|
||||||
|
|
||||||
|
#define REG_TXQ_CMD (0x80) /* TXQCR */
|
||||||
|
#define TXQ_AUTO_ENQUEUE (0x0004) /* Enable enqueue tx frames from tx buffer automatically */
|
||||||
|
#define TXQ_MEM_AVAILABLE_INT (0x0002) /* Enable generate interrupt when tx memory is available */
|
||||||
|
#define TXQ_ENQUEUE (0x0001) /* Enable enqueue tx frames one frame at a time */
|
||||||
|
|
||||||
|
#define REG_RXQ_CMD (0x82) /* RXQCR */
|
||||||
|
#define RXQ_STAT_TIME_INT (0x1000) /* RX interrupt is occured by timer duration */
|
||||||
|
#define RXQ_STAT_BYTE_CNT_INT (0x0800) /* RX interrupt is occured by byte count threshold */
|
||||||
|
#define RXQ_STAT_FRAME_CNT_INT (0x0400) /* RX interrupt is occured by frame count threshold */
|
||||||
|
#define RXQ_TWOBYTE_OFFSET (0x0200) /* Enable adding 2-byte before frame header for IP aligned with DWORD */
|
||||||
|
#define RXQ_TIME_INT (0x0080) /* Enable RX interrupt by timer duration */
|
||||||
|
#define RXQ_BYTE_CNT_INT (0x0040) /* Enable RX interrupt by byte count threshold */
|
||||||
|
#define RXQ_FRAME_CNT_INT (0x0020) /* Enable RX interrupt by frame count threshold */
|
||||||
|
#define RXQ_AUTO_DEQUEUE (0x0010) /* Enable release rx frames from rx buffer automatically */
|
||||||
|
#define RXQ_START (0x0008) /* Start QMU transfer operation */
|
||||||
|
#define RXQ_CMD_FREE_PACKET (0x0001) /* Manual dequeue (release the current frame from RxQ) */
|
||||||
|
|
||||||
|
#define RXQ_CMD_CNTL (RXQ_FRAME_CNT_INT|RXQ_AUTO_DEQUEUE)
|
||||||
|
|
||||||
|
#define REG_TX_ADDR_PTR (0x84) /* TXFDPR */
|
||||||
|
#define REG_RX_ADDR_PTR (0x86) /* RXFDPR */
|
||||||
|
#define ADDR_PTR_AUTO_INC (0x4000) /* Enable Frame data pointer increments automatically */
|
||||||
|
#define ADDR_PTR_MASK (0x03ff) /* Address pointer mask */
|
||||||
|
|
||||||
|
#define REG_RX_TIME_THRES (0x8C) /* RXDTTR */
|
||||||
|
#define RX_TIME_THRESHOLD_MASK (0xFFFF) /* Set receive timer duration threshold */
|
||||||
|
|
||||||
|
#define REG_RX_BYTE_CNT_THRES (0x8E) /* RXDBCTR */
|
||||||
|
#define RX_BYTE_THRESHOLD_MASK (0xFFFF) /* Set receive byte count threshold */
|
||||||
|
|
||||||
|
#define REG_INT_MASK (0x90) /* IER */
|
||||||
|
#define INT_PHY (0x8000) /* Enable link change interrupt */
|
||||||
|
#define INT_TX (0x4000) /* Enable transmit done interrupt */
|
||||||
|
#define INT_RX (0x2000) /* Enable receive interrupt */
|
||||||
|
#define INT_RX_OVERRUN (0x0800) /* Enable receive overrun interrupt */
|
||||||
|
#define INT_TX_STOPPED (0x0200) /* Enable transmit process stopped interrupt */
|
||||||
|
#define INT_RX_STOPPED (0x0100) /* Enable receive process stopped interrupt */
|
||||||
|
#define INT_TX_SPACE (0x0040) /* Enable transmit space available interrupt */
|
||||||
|
#define INT_RX_WOL_FRAME (0x0020) /* Enable WOL on receive wake-up frame detect interrupt */
|
||||||
|
#define INT_RX_WOL_MAGIC (0x0010) /* Enable WOL on receive magic packet detect interrupt */
|
||||||
|
#define INT_RX_WOL_LINKUP (0x0008) /* Enable WOL on link up detect interrupt */
|
||||||
|
#define INT_RX_WOL_ENERGY (0x0004) /* Enable WOL on energy detect interrupt */
|
||||||
|
#define INT_RX_SPI_ERROR (0x0002) /* Enable receive SPI bus error interrupt */
|
||||||
|
#define INT_RX_WOL_DELAY_ENERGY (0x0001) /* Enable WOL on delay energy detect interrupt */
|
||||||
|
#define INT_MASK ( INT_RX | INT_TX | INT_PHY )
|
||||||
|
|
||||||
|
#define REG_INT_STATUS (0x92) /* ISR */
|
||||||
|
|
||||||
|
#define REG_RX_FRAME_CNT_THRES (0x9C) /* RXFCTFC */
|
||||||
|
#define RX_FRAME_CNT_MASK (0xFF00) /* Received frame count mask */
|
||||||
|
#define RX_FRAME_THRESHOLD_MASK (0x00FF) /* Set receive frame count threshold mask */
|
||||||
|
|
||||||
|
#define REG_TX_TOTAL_FRAME_SIZE (0x9E) /* TXNTFSR */
|
||||||
|
#define TX_TOTAL_FRAME_SIZE_MASK (0xFFFF) /* Set next total tx frame size mask */
|
||||||
|
|
||||||
|
/*
|
||||||
|
* MAC Address Hash Table Control Registers
|
||||||
|
* (Offset 0xA0 - 0xA7)
|
||||||
|
*/
|
||||||
|
#define REG_MAC_HASH_0 (0xA0) /* MAHTR0 */
|
||||||
|
#define REG_MAC_HASH_1 (0xA1)
|
||||||
|
|
||||||
|
#define REG_MAC_HASH_2 (0xA2) /* MAHTR1 */
|
||||||
|
#define REG_MAC_HASH_3 (0xA3)
|
||||||
|
|
||||||
|
#define REG_MAC_HASH_4 (0xA4) /* MAHTR2 */
|
||||||
|
#define REG_MAC_HASH_5 (0xA5)
|
||||||
|
|
||||||
|
#define REG_MAC_HASH_6 (0xA6) /* MAHTR3 */
|
||||||
|
#define REG_MAC_HASH_7 (0xA7)
|
||||||
|
|
||||||
|
/*
|
||||||
|
* QMU Receive Queue Watermark Control Registers
|
||||||
|
* (Offset 0xB0 - 0xB5)
|
||||||
|
*/
|
||||||
|
#define REG_RX_LOW_WATERMARK (0xB0) /* FCLWR */
|
||||||
|
#define RX_LOW_WATERMARK_MASK (0x0FFF) /* Set QMU RxQ low watermark mask */
|
||||||
|
|
||||||
|
#define REG_RX_HIGH_WATERMARK (0xB2) /* FCHWR */
|
||||||
|
#define RX_HIGH_WATERMARK_MASK (0x0FFF) /* Set QMU RxQ high watermark mask */
|
||||||
|
|
||||||
|
#define REG_RX_OVERRUN_WATERMARK (0xB4) /* FCOWR */
|
||||||
|
#define RX_OVERRUN_WATERMARK_MASK (0x0FFF) /* Set QMU RxQ overrun watermark mask */
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Global Control Registers
|
||||||
|
* (Offset 0xC0 - 0xD3)
|
||||||
|
*/
|
||||||
|
#define REG_CHIP_ID (0xC0) /* CIDER */
|
||||||
|
#define CHIP_ID_MASK (0xFFF0) /* Family ID and chip ID mask */
|
||||||
|
#define REVISION_MASK (0x000E) /* Chip revision mask */
|
||||||
|
#define CHIP_ID_SHIFT (4)
|
||||||
|
#define REVISION_SHIFT (1)
|
||||||
|
#define CHIP_ID_8851_16 (0x8870) /* KS8851-16/32MQL chip ID */
|
||||||
|
|
||||||
|
#define REG_LED_CTRL (0xC6) /* CGCR */
|
||||||
|
#define LED_CTRL_SEL1 (0x8000) /* Select LED3/LED2/LED1/LED0 indication */
|
||||||
|
#define LED_CTRL_SEL0 (0x0200) /* Select LED3/LED2/LED1/LED0 indication */
|
||||||
|
|
||||||
|
#define REG_IND_IACR (0xC8) /* IACR */
|
||||||
|
#define TABLE_READ (0x1000) /* Indirect read */
|
||||||
|
#define TABLE_MIB (0x0C00) /* Select MIB counter table */
|
||||||
|
#define TABLE_ENTRY_MASK (0x001F) /* Set table entry to access */
|
||||||
|
|
||||||
|
#define REG_IND_DATA_LOW (0xD0) /* IADLR */
|
||||||
|
#define REG_IND_DATA_HIGH (0xD2) /* IADHR */
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Power Management Control Registers
|
||||||
|
* (Offset 0xD4 - 0xD7)
|
||||||
|
*/
|
||||||
|
#define REG_POWER_CNTL (0xD4) /* PMECR */
|
||||||
|
#define PME_DELAY_ENABLE (0x4000) /* Enable the PME output pin assertion delay */
|
||||||
|
#define PME_ACTIVE_HIGHT (0x1000) /* PME output pin is active high */
|
||||||
|
#define PME_FROM_WKFRAME (0x0800) /* PME asserted when wake-up frame is detected */
|
||||||
|
#define PME_FROM_MAGIC (0x0400) /* PME asserted when magic packet is detected */
|
||||||
|
#define PME_FROM_LINKUP (0x0200) /* PME asserted when link up is detected */
|
||||||
|
#define PME_FROM_ENERGY (0x0100) /* PME asserted when energy is detected */
|
||||||
|
#define PME_EVENT_MASK (0x0F00) /* PME asserted event mask */
|
||||||
|
#define WAKEUP_AUTO_ENABLE (0x0080) /* Enable auto wake-up in energy mode */
|
||||||
|
#define WAKEUP_NORMAL_AUTO_ENABLE (0x0040) /* Enable auto goto normal mode from energy detecion mode */
|
||||||
|
#define WAKEUP_FROM_WKFRAME (0x0020) /* Wake-up from wake-up frame event detected */
|
||||||
|
#define WAKEUP_FROM_MAGIC (0x0010) /* Wake-up from magic packet event detected */
|
||||||
|
#define WAKEUP_FROM_LINKUP (0x0008) /* Wake-up from link up event detected */
|
||||||
|
#define WAKEUP_FROM_ENERGY (0x0004) /* Wake-up from energy event detected */
|
||||||
|
#define WAKEUP_EVENT_MASK (0x003C) /* Wake-up event mask */
|
||||||
|
#define POWER_STATE_D1 (0x0003) /* Power saving mode */
|
||||||
|
#define POWER_STATE_D3 (0x0002) /* Power down mode */
|
||||||
|
#define POWER_STATE_D2 (0x0001) /* Power detection mode */
|
||||||
|
#define POWER_STATE_D0 (0x0000) /* Normal operation mode (default) */
|
||||||
|
#define POWER_STATE_MASK (0x0003) /* Power management mode mask */
|
||||||
|
|
||||||
|
#define REG_WAKEUP_TIME (0xD6) /* GSWUTR */
|
||||||
|
#define WAKEUP_TIME (0xFF00) /* Min time (sec) wake-uo after detected energy */
|
||||||
|
#define GOSLEEP_TIME (0x00FF) /* Min time (sec) before goto sleep when in energy mode */
|
||||||
|
|
||||||
|
/*
|
||||||
|
* PHY Control Registers
|
||||||
|
* (Offset 0xD8 - 0xF9)
|
||||||
|
*/
|
||||||
|
#define REG_PHY_RESET (0xD8) /* PHYRR */
|
||||||
|
#define PHY_RESET (0x0001) /* Reset PHY */
|
||||||
|
|
||||||
|
#define REG_PHY_CNTL (0xE4) /* P1MBCR */
|
||||||
|
#define PHY_SPEED_100MBIT (0x2000) /* Force PHY 100Mbps */
|
||||||
|
#define PHY_AUTO_NEG_ENABLE (0x1000) /* Enable PHY auto-negotiation */
|
||||||
|
#define PHY_POWER_DOWN (0x0800) /* Set PHY power-down */
|
||||||
|
#define PHY_AUTO_NEG_RESTART (0x0200) /* Restart PHY auto-negotiation */
|
||||||
|
#define PHY_FULL_DUPLEX (0x0100) /* Force PHY in full duplex mode */
|
||||||
|
#define PHY_HP_MDIX (0x0020) /* Set PHY in HP auto MDI-X mode */
|
||||||
|
#define PHY_FORCE_MDIX (0x0010) /* Force MDI-X */
|
||||||
|
#define PHY_AUTO_MDIX_DISABLE (0x0008) /* Disable auto MDI-X */
|
||||||
|
#define PHY_TRANSMIT_DISABLE (0x0002) /* Disable PHY transmit */
|
||||||
|
#define PHY_LED_DISABLE (0x0001) /* Disable PHY LED */
|
||||||
|
|
||||||
|
#define REG_PHY_STATUS (0xE6) /* P1MBSR */
|
||||||
|
#define PHY_100BT4_CAPABLE (0x8000) /* 100 BASE-T4 capable */
|
||||||
|
#define PHY_100BTX_FD_CAPABLE (0x4000) /* 100BASE-TX full duplex capable */
|
||||||
|
#define PHY_100BTX_CAPABLE (0x2000) /* 100BASE-TX half duplex capable */
|
||||||
|
#define PHY_10BT_FD_CAPABLE (0x1000) /* 10BASE-TX full duplex capable */
|
||||||
|
#define PHY_10BT_CAPABLE (0x0800) /* 10BASE-TX half duplex capable */
|
||||||
|
#define PHY_AUTO_NEG_ACKNOWLEDGE (0x0020) /* Auto-negotiation complete */
|
||||||
|
#define PHY_AUTO_NEG_CAPABLE (0x0008) /* Auto-negotiation capable */
|
||||||
|
#define PHY_LINK_UP (0x0004) /* PHY link is up */
|
||||||
|
#define PHY_EXTENDED_CAPABILITY (0x0001) /* PHY extended register capable */
|
||||||
|
|
||||||
|
#define REG_PHY_ID_LOW (0xE8) /* PHY1ILR */
|
||||||
|
#define REG_PHY_ID_HIGH (0xEA) /* PHY1IHR */
|
||||||
|
|
||||||
|
#define REG_PHY_AUTO_NEGOTIATION (0xEC) /* P1ANAR */
|
||||||
|
#define PHY_AUTO_NEG_SYM_PAUSE (0x0400) /* Advertise pause capability */
|
||||||
|
#define PHY_AUTO_NEG_100BTX_FD (0x0100) /* Advertise 100 full-duplex capability */
|
||||||
|
#define PHY_AUTO_NEG_100BTX (0x0080) /* Advertise 100 half-duplex capability */
|
||||||
|
#define PHY_AUTO_NEG_10BT_FD (0x0040) /* Advertise 10 full-duplex capability */
|
||||||
|
#define PHY_AUTO_NEG_10BT (0x0020) /* Advertise 10 half-duplex capability */
|
||||||
|
#define PHY_AUTO_NEG_SELECTOR (0x001F) /* Selector field mask */
|
||||||
|
#define PHY_AUTO_NEG_802_3 (0x0001) /* 802.3 */
|
||||||
|
|
||||||
|
#define REG_PHY_REMOTE_CAPABILITY (0xEE) /* P1ANLPR */
|
||||||
|
#define PHY_REMOTE_SYM_PAUSE (0x0400) /* Link partner pause capability */
|
||||||
|
#define PHY_REMOTE_100BTX_FD (0x0100) /* Link partner 100 full-duplex capability */
|
||||||
|
#define PHY_REMOTE_100BTX (0x0080) /* Link partner 100 half-duplex capability */
|
||||||
|
#define PHY_REMOTE_10BT_FD (0x0040) /* Link partner 10 full-duplex capability */
|
||||||
|
#define PHY_REMOTE_10BT (0x0020) /* Link partner 10 half-duplex capability */
|
||||||
|
|
||||||
|
#define REG_PORT_LINK_MD (0xF4) /* P1SCLMD */
|
||||||
|
#define PORT_CABLE_10M_SHORT (0x8000) /* Cable length is less than 10m short */
|
||||||
|
#define PORT_CABLE_STAT_FAILED (0x6000) /* Cable diagnostic test fail */
|
||||||
|
#define PORT_CABLE_STAT_SHORT (0x4000) /* Short condition detected in the cable */
|
||||||
|
#define PORT_CABLE_STAT_OPEN (0x2000) /* Open condition detected in the cable */
|
||||||
|
#define PORT_CABLE_STAT_NORMAL (0x0000) /* Normal condition */
|
||||||
|
#define PORT_CABLE_DIAG_RESULT (0x6000) /* Cable diagnostic test result mask */
|
||||||
|
#define PORT_START_CABLE_DIAG (0x1000) /* Enable cable diagnostic test */
|
||||||
|
#define PORT_FORCE_LINK (0x0800) /* Enable force link pass */
|
||||||
|
#define PORT_POWER_SAVING (0x0400) /* Disable power saving */
|
||||||
|
#define PORT_REMOTE_LOOPBACK (0x0200) /* Enable remote loopback at PHY */
|
||||||
|
#define PORT_CABLE_FAULT_COUNTER (0x01FF) /* Cable length distance to the fault */
|
||||||
|
|
||||||
|
#define REG_PORT_CTRL (0xF6) /* P1CR */
|
||||||
|
#define PORT_LED_OFF (0x8000) /* Turn off all the port LEDs (LED3/LED2/LED1/LED0) */
|
||||||
|
#define PORT_TX_DISABLE (0x4000) /* Disable port transmit */
|
||||||
|
#define PORT_AUTO_NEG_RESTART (0x2000) /* Restart auto-negotiation */
|
||||||
|
#define PORT_POWER_DOWN (0x0800) /* Set port power-down */
|
||||||
|
#define PORT_AUTO_MDIX_DISABLE (0x0400) /* Disable auto MDI-X */
|
||||||
|
#define PORT_FORCE_MDIX (0x0200) /* Force MDI-X */
|
||||||
|
#define PORT_AUTO_NEG_ENABLE (0x0080) /* Enable auto-negotiation */
|
||||||
|
#define PORT_FORCE_100_MBIT (0x0040) /* Force PHY 100Mbps */
|
||||||
|
#define PORT_FORCE_FULL_DUPLEX (0x0020) /* Force PHY in full duplex mode */
|
||||||
|
#define PORT_AUTO_NEG_SYM_PAUSE (0x0010) /* Advertise pause capability */
|
||||||
|
#define PORT_AUTO_NEG_100BTX_FD (0x0008) /* Advertise 100 full-duplex capability */
|
||||||
|
#define PORT_AUTO_NEG_100BTX (0x0004) /* Advertise 100 half-duplex capability */
|
||||||
|
#define PORT_AUTO_NEG_10BT_FD (0x0002) /* Advertise 10 full-duplex capability */
|
||||||
|
#define PORT_AUTO_NEG_10BT (0x0001) /* Advertise 10 half-duplex capability */
|
||||||
|
|
||||||
|
#define REG_PORT_STATUS (0xF8) /* P1SR */
|
||||||
|
#define PORT_HP_MDIX (0x8000) /* Set PHY in HP auto MDI-X mode */
|
||||||
|
#define PORT_REVERSED_POLARITY (0x2000) /* Polarity is reversed */
|
||||||
|
#define PORT_RX_FLOW_CTRL (0x1000) /* Reeive flow control feature is active */
|
||||||
|
#define PORT_TX_FLOW_CTRL (0x0800) /* Transmit flow control feature is active */
|
||||||
|
#define PORT_STAT_SPEED_100MBIT (0x0400) /* Link is 100Mbps */
|
||||||
|
#define PORT_STAT_FULL_DUPLEX (0x0200) /* Link is full duplex mode */
|
||||||
|
#define PORT_MDIX_STATUS (0x0080) /* Is MDI */
|
||||||
|
#define PORT_AUTO_NEG_COMPLETE (0x0040) /* Auto-negotiation complete */
|
||||||
|
#define PORT_STATUS_LINK_GOOD (0x0020) /* PHY link is up */
|
||||||
|
#define PORT_REMOTE_SYM_PAUSE (0x0010) /* Link partner pause capability */
|
||||||
|
#define PORT_REMOTE_100BTX_FD (0x0008) /* Link partner 100 full-duplex capability */
|
||||||
|
#define PORT_REMOTE_100BTX (0x0004) /* Link partner 100 half-duplex capability */
|
||||||
|
#define PORT_REMOTE_10BT_FD (0x0002) /* Link partner 10 full-duplex capability */
|
||||||
|
#define PORT_REMOTE_10BT (0x0001) /* Link partner 10 half-duplex capability */
|
||||||
|
|
||||||
|
#endif /* KSZ8851SNL_REG_H_INCLUDED */
|
||||||
Reference in New Issue
Block a user