44 lines
3.5 KiB
Plaintext
44 lines
3.5 KiB
Plaintext
|
=============================================================================
|
||
|
|
List of methods in project: RTOSDemo
|
||
|
|
|
||
|
|
THIS TEXT DESCRIPTION IS GENERATED BY THE TOOL. DO NOT MODIFY IT.
|
||
|
|
=============================================================================
|
||
|
|
|
||
|
|
Module "TickTimer" (bean TimerInt)
|
||
|
|
TickTimer_Enable -Enable the bean - it starts the timer. Events may be generated ("DisableEvent"/"EnableEvent").
|
||
|
|
TickTimer_SetPeriodTicks16 -This method sets the new period of the generated events. The period is expressed in CPU [ticks]
|
||
|
|
as a 16-bit unsigned integer number. This method is available only if runtime setting type 'from interval' is
|
||
|
|
selected in the <Timing dialog box> in Runtime setting area.
|
||
|
|
TickTimer_SetPeriodTicks32 -This method sets the new period of the generated events. The period is expressed in CPU [ticks]
|
||
|
|
as a 32-bit unsigned integer number. This method is available only if runtime setting type 'from interval' is
|
||
|
|
selected in the <Timing dialog box> in Runtime setting area.
|
||
|
|
TickTimer_SetPeriodUS -This method sets the new period of the generated events. The period is expressed in [microseconds] as
|
||
|
|
a 16-bit unsigned integer number. This method is available only if runtime setting type 'from interval' is
|
||
|
|
selected in the <Timing dialog box> in Runtime setting area.
|
||
|
|
TickTimer_SetPeriodMS -This method sets the new period of the generated events. The period is expressed in [miliseconds] as
|
||
|
|
a 16-bit unsigned integer number. This method is available only if runtime setting type 'from interval' is
|
||
|
|
selected in the <Timing dialog box> in Runtime setting area.
|
||
|
|
TickTimer_SetFreqHz -This method sets the new frequency of the generated events. The frequency is expressed in [Hz] as a
|
||
|
|
16-bit unsigned integer number. This method is available only if runtime setting type 'from interval' is
|
||
|
|
selected in the <Timing dialog box> in Runtime setting area.
|
||
|
|
|
||
|
|
Module "Byte1" (bean ByteIO)
|
||
|
|
Byte1_PutBit -Put the specified value to the specified bit/pin of the Input/Output bean. If direction is [input] saves the
|
||
|
|
value to a memory or a register, this value will be written to the pin after switching to the output mode -
|
||
|
|
using [SetDir(TRUE)]. If direction is [output] writes the value to the pin.
|
||
|
|
Byte1_NegBit -Negate (invert) the specified bit of the Input/Output bean. It is the same as [PutBit(Bit,!GetBit(Bit))].
|
||
|
|
|
||
|
|
Module "COM0" (bean AsynchroSerial)
|
||
|
|
COM0_SetBaudRateMode -This method changes the channel communication speed (baud rate). This method can be used only if you
|
||
|
|
specify a list of possible period settings at design time (see <Timing dialog box> - Runtime setting - from a
|
||
|
|
list of values). Each of these settings constitutes a mode and Processor Expert^[TM] assigns them a mode
|
||
|
|
identifier. The prescaler and compare values corresponding to each mode are calculated at design time. You may
|
||
|
|
switch modes at runtime by referring only to a mode identifier. No run-time calculations are performed, all the
|
||
|
|
calculations are performed at design time.
|
||
|
|
|
||
|
|
Module "Cpu" (bean MC9S12DP256_112)
|
||
|
|
Cpu_EnableInt -Enable maskable interrupts
|
||
|
|
Cpu_DisableInt -Disable maskable interrupts
|
||
|
|
|
||
|
|
=============================================================================
|